IR6000 profile ramp to solder AM4 Socket

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Inforgalaxie
    Member
    • Apr 2023
    • 40
    • Portugal
    #1

    IR6000 profile ramp to solder AM4 Socket

    Hello I have a IR6000 and i need solder new AM4 Socket in the motherboard.
    I was solder one but damage the plastic socket...
    Can you tell me what is the best profile ramp to do that?

    Thanks!
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • howardc64
      A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
      by howardc64
      Problem

      This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
      08-04-2024, 10:36 PM
    • acedogblast
      Guide to transplant MEC1503 EC chip and EEPROM reprogamming for T14s gen 2 and X13 gen 2
      by acedogblast
      This is a guide that I am writing for helping others to replace their MEC1503 EC chip if it breaks (or to get around an inconvenient prompt to the BIOS). This forum has been extremely helpful to me so I would like to contribute to help others. I will tell you right now that this task is very difficult to do. You MUST have experience and tools to do precision micro-soldering, BGA reballing, trace repair, and general laptop repair skills.

      There are some specialty tools needed to do this task. The replacement MEC1503 chips can be acquired from Aliexpress. Do not buy the bare chips as...
      11-02-2024, 05:13 PM
    • corrize
      Best way to solder LVDS connector for beginner (and qfn) ?
      by corrize
      Hello, I'm a beginner for micro soldering. Right now I have some difficult to solder a qfn 20, I guess I put too much solder on the thermal-ground pad, the result is a corner of chip wich don't touch the board (last try).

      I use a wire solder with hot air, I tin the board and chip before with iron and I use good flux.

      I will have to solder a LVDS connector (40 pins, laptop pc), I saw a solder paste in seringe, good quality (it does not scatter).
      See the test :
      https://youtu.be/bNAzC-EvqHs?t=1767

      With hot air from bellow the board, that's...
      03-09-2023, 02:57 AM
    • Kemer
      Led status indicator light transfer plastic
      by Kemer
      Hello, the LED status indicators on my Lenovo Z580 are not working. Actually the motherboard LEDs are working but the light doesn''t coming to the front view. The plastic part is which you can see in photo must transfer the light to the frontview but just half of the plastic is illuminating.

      There are three status indicators on the front (power, battery, caps lock), and none of them are illuminated.

      The plastic piece doesn't appear to be broken.

      1. What are your suggestions for resolving this issue?

      2. Is the plastic piece made of special ma...
      08-19-2025, 07:02 PM
    • warsztat
      Acer AN515-57-577G JDIMM1 socket not working.
      by warsztat
      Hello, Acer AN515-57-577G JDIMM1 socket does not work. GH51G LA-L181P, 2x DDR4 RAM, both good, both work well in JDIMM2, neither works in JDIMM1. The laptop displays BIOS, when the JDIMM2 socket is occupied, you can run Linux on USB, then everything seems to work ok, there is internet access and you can browse the contents of the 512 GB SSD in Windows, but starting Windows ends with an eternal spinning circle, maybe there are corrupted files. When the RAM is inserted into the JDIMM1 socket, the laptop starts but there is no image and the downloaded current does not change and the output is ~2.25A....
      11-18-2024, 09:13 AM
    • Loading...
    • No more items.
    Working...