SY8388B3RHC alternative

yaso143

Member

Join Date: May 2021

Posts: 49

Country: philippines
#1

SY8388B3RHC alternative

07-05-2023, 03:40 PM

whats the alternative for this buck regulator? icant find any shops that sells this one here is the descrption

High Efficiency Fast Response, 8A, 28V Input, Synchronous Buck Regulator with 100mA 3.3V LDO

Vin_min (V) 4
Vin_max (V) twenty four
Vo_min (V) 3.338
Io_max (A) 8
Vref Accuracy ±1%
Fsw (MHz) 0.6
Iq (uA) 85
package QFN2.5x2.5-16
Protection Mode Latch-off SCP
Features / Special Functions Power Good Indicator, Auto-Discharge
Tags: None

Previous template Next

Reolink RLC-410-5MP - buck convertor

by jm1234

Hi,
it's a PoE camera and it stopped working. Using thermal image I identified failing component U22 marked as 16AF which seems to be buck convertor TI https://www.alldatasheet.net/datashe...62569DBVR.html. I took it out and It is inteed shorted on the output. However, after I took it out, the resistance between the output pads (on the board) still shows 190ohm, is that bit low?
Another issue is, seems to me I must be missing one of the tiny resistors R810 that should make up the voltage devider for the buck convertor. Honestly I did this months ago, I cannot...
- Channel: Troubleshooting Printers, Copiers, Scanners and other Imaging & Printing Devices
07-14-2025, 04:30 AM
Protecting against over volts when fitting a buck regulator controller. Good Idea?

by dicky96

Hi guys
Here is a general question and I would like to hear your thoughts on it

I've just replaced a very small 11 contact MP2329 QFN on a motherboard

This supplies 1.8V STBY to the PCH - but the faulty one was only giving 0.7V

Anyway I fitted it, but it is very close to the DIMM sockets and I can not clearly see down one side of it to make sure it has soldered properly ,even shining a torch down there. The other sides look OK under the microscope and also in a jewellers loop. This is the side that has two resistors that set the output voltage
...
- Channel: General Electronics Technical Discussion
04-30-2021, 07:37 AM
HP 2311 display, 3.3v regulator fried, need help to replace

by disorder

hello,

i have a hp display 2311 to repair, totaly dead
on the board, il have 2 capacitor 470µf that are dead and the 3.3v regulator : ax6630-33
i have no such regulator, can i replace this one with a mic5209-33 (3.3v outpout regulator too) ?

thank you
- Channel: Troubleshooting Computer Displays
07-27-2025, 04:34 AM
Hisee CCTV monitor Buck regulator chip ID help required.

by zen

Hi all, won't go into details but managed to cook it myself.

Has two sets of codes on it.

Top code JWN8T

Just below code 2GL 4B

PCB code ZM11E-T30 V2.1

Out of a Hiseen CCTV monitor with no model of course....
- Channel: Troubleshooting Computer Displays
10-06-2022, 05:17 AM
uP0109: 2A Ultra Low Dropout Linear Regulator equivalent substitute

by bilux

Hello everyone,
I want to find a replacement for uP0109 8pins, and i found this parts:

uP0109 is "2A Ultra Low Dropout Linear Regulator"
RT9199 is "Cost-Effective, 2A Peak Sink/Source Bus Termination Regulator"
FP6137C is "2A BUS TERMINATION REGULATOR"

can replace uP0109 by RT9199 or FP6137C ?
- Channel: General Electronics Technical Discussion
11-01-2024, 12:00 PM
Loading...
No more items.

SY8388B3RHC alternative

SY8388B3RHC alternative

Related Topics