Magnavox Power supply help 37MF321 LCD TV - Constant 24v inverter voltage...

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Zalinar
    Zalinar
    • Sep 2012
    • 10
    • USA

    #1

    Magnavox Power supply help 37MF321 LCD TV - Constant 24v inverter voltage...

    Hi, I am working on a 3138 103 6338.1 power supply.

    I have replaced all electrolytics and several other items. I have tested all Diodes and transistors.

    The main problem was a shorted mosfet 7062 which I replaced with a 13A W13NK80Z rather than with an 18A W18NK80Z which I have on order.

    All of the voltages are what they are supposed to be at.

    The issue:

    The 24V to the inverters is always on. From my experience, this should be off until 3v is applied to the standby pin 9 on connector 1089. The power supply does turn on when the 3v is applied. You can hear the transistor powering up. There is no change in voltage outputs however.

    What could be causing the 24v on the inverter bus to be present even when the supply is 'off?'

    The 24v at the inverter pins is also at full current when the supply is plugged in, no matter if it is in the On or Off state. I hooked a 40W light bulb to the output to test this, and the filament glows the same in either state...

    I only have the power supply board - no tv or other boards.

    Any help is much appreciated!

Related Topics

Collapse

  • sam_sam_sam
    Adjustable Boost Power Supply DC-DC Constant Voltage Current Charging Module
    by sam_sam_sam
    I want to know if I could hook up a solar panels to this boost converter would I have any issues doing and I would have issues what would they be

    Adjustable Boost Power Supply DC-DC Constant Voltage Current Charging Module

    https://www.ebay.com/itm/116497313155?var=416785404161


    Here are some of the description from the eBay seller

    The main parameters:
    1. Product name: High-power non-isolated DC boost module power supply.
    2. Product model: 100A2000W.
    3. Input voltage: DC12V-60V.
    4. Input current: 100A (maximum)....
    05-18-2025, 09:45 AM
  • Tynan Dill
    Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
    by Tynan Dill
    I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

    Upon bringing it home and plugging it up, it showed a standby light.

    I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

    The screen seems to blackout and stay black, but with a flashlight I can see the display.

    With my Playstation 4 connected via HDMI, and running a game I can hear sound.

    Assuming...
    11-22-2024, 01:46 PM
  • Jembang
    coocaa 50S5G smart tv dropped voltage when connecting power supply to mainboard
    by Jembang
    good day hoping someone can lend a hand, im repairing smart tv 50 inch, status when turning on back light is dim but you can see the tv logo then slowly fading out to black, i check the supply to tcon, i only read 5+v, must be 12v, i removed lvds cable and check voltage to mainboard turned on its also 5v, then i remove the cable mainboard to power supply, i read 12v in power supply, thinking that the problem is in the mainboard, coz theres 12v in power supply, i also check while turning on checking volts in main board 12v dropping to 5v, im just new repairing in TV, hope someone see my post t...
    11-01-2024, 09:55 AM
  • Document Archive
    LM358 LM358S-13 Datasheet
    by Document Archive
    The LM358 LM358S-13 consists of two independent, high gain, internally frequency compensated operational amplifiers which were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage.

    Application areas include transducer amplifiers, dc gain blocks and all the conventional op amp circuits which now can be more easily implemented in single power supply systems. For example, the LM358 series can be directly...
    10-07-2024, 04:12 AM
  • sam_sam_sam
    How to modify a switching power supply that has voltage/current adjustable but powering it from a battery pack
    by sam_sam_sam
    I have been pondering this question for a while but now I have see if this doable but I need to answer this question once and for all

    I would like to know how to safely do this undertaking my first thought is to solder wires to the main filtering capacitors and see
    what voltage I am getting and seeing if I can build a battery pack with voltage or not and if

    I can find a BMS balancing protection board at this voltage level and weather or not do I have use more than one BMS balancing protection board...
    05-11-2025, 05:22 PM
  • Loading...
  • No more items.
Working...