UN55D6000 - Multiple issues, now no standby light

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • fuxxy
    Badcaps Veteran
    • Jan 2013
    • 318
    • USA
    #1

    UN55D6000 - Multiple issues, now no standby light

    UN55D6000 I've posted about before.

    Initially had bad backlights, of which both entire strips were replaced.
    Then TV started not staying off. Every poweroff command was recognized, TV would power off then power right back on, even with nothing attached.

    Now, no output at all. No red Power LED, No response to remote. No clicking or coil whine.

    From other threads, tested various outputs on the PSU. Noticed that when the mainboard was unplugged, the backlights would turn on.

    Backlight Connector CNL802:
    Logic board unplugged:
    pin 1 = 335V
    pin 3 = 167.4V
    pin 5 = 167.4V
    pin 7 = 1.113V
    pin 9 = .603V
    pin 10 = 0.0V

    Main filter cap CP806:
    Logic Board unplugged: 330v DC
    Logic Board plugged: 169.5v DC

    Mainboard Connector at PSU (mainboard unplugged)
    Code:
    2 (n/c)      | 1 (n/c)
4 (EPWM) 3.19v   | 3 (B13V)12.72v
6 (n/c)      | 5 (B13V)12.7v
8 (BLU_ON) 2.98v  | 7 (Vamp)16.83v
10 (GND) 0v    | 9 (Vamp) 16.83v
12 (GND) 0v    | 11 (GND)0v
14 (A5V) 5.33v   | 13 (B5V)5.33v
16 (PS-ON) 3.33v  | 15 (B5V)5.33v

    After having the logic board unplugged for the hour or so it took to take measurements, I plugged the logic board back in and the TV turned on.

    Do you guys share my assumption? Power board most likely good. Backlights most likely good. Logic board is suspect.

    Are there any component level diagnosis I can do for the logic board?
    Attached Files
    Last edited by fuxxy; 12-23-2022, 08:51 PM.
    Tags: None
    • Davi.p
      Hobbist Tech
      • Sep 2009
      • 4358
      • Italy - Milan
      #2
      Re: UN55D6000 - Multiple issues, now no standby light

      You must rewrite the Weltrend MCU..

        Comment

        Previous template Next

        Related Topics

        Collapse
        • tvguy12012012120
          Zombie Samsung UN55NU6900F dead / no standby voltage - randomly came to life after hours of troubleshooting then died
          by tvguy12012012120
          This is my first attempt at troubleshooting a board like this, I know I could just buy a new board but I'm curious to figure out how this works. I've been testing different components in the evenings this week and I think the problem is with the IC failing to start up for some reason. When the board is plugged in there is no standby voltage.

          Then today it randomly sprung to life like a zombie but shortly died thereafter. I have no idea why it would have done that and its the first time I've seen it running. I discharged capacitors on the board last night, then it was sitting today....
          02-07-2025, 05:13 PM
        • fharris1977
          Vizio D50u-D1 Dead Set No Standby
          by fharris1977
          Hi. I got a Vizio with no power or standby, and won't turn on with remote or button. I checked the voltages on the connector and all read 0.00V or nearly 0(0.050 ON/OFF pin). None of the pins are labeled STB for standby although I do see some 5V pins. Other than the obvious standby led, which isn't coming on, is there a way to check for standby voltage on this PS. I'm trying to see if my problem is the PS or mainboard. Some Vizios I have fixed with no standby led me to think it was the PS but it turned out being the mainboard. Any experience with this set would be greatly appreciated.
          1 Photo
          12-28-2023, 10:25 AM
        • ohren
          Upgrading a Samsung ue55nu7096u with logic board from an ue55ru7105k -- good idea?
          by ohren
          I hope this is the right forum to post in despite not technically being a repair, but still a question of swapping boards.

          I thought I'd explore the possibility to upgrade an existing working Samsung ue55nu7096u with the logic board (and power board if needed) of a newer model (ue55ru7105k) of the same size and appearance (and resolution). The reason being I'd like the extra inputs of that board including component in, an extra HDMI port and bluetooth. Its panel is broken so I have no use for the board otherwise.

          The models launched in 2018 and 2019 respectively....
          09-08-2023, 05:24 PM
        • Crystaleyes
          Samsung BN44-00259A standby question
          by Crystaleyes
          Hi all.

          I started a thread while back regarding TV power supply standby circuitry as it is something I am not quite on top of.
          SMPS theory and function is becoming more familiar, however the standby part is still a bit of a mystery.

          Anyway, a friend has this TV with the above mentioned power supply board which has no standby voltage, nor any other voltages leaving the board.
          The mains AC comes in fine, gets filtered and rectified with power is on the main filter cap as well as the transformer and drain pins of the ICE3B0665J, but that's it.
          ...
          08-11-2023, 05:15 AM
        • howardc64
          Pioneer PN50951-22U dead
          by howardc64
          Got this free 2+ year old TV. Dead. Standby Light on. Power on (button+remote) does nothing (no screen display, backlight, SPDIF light, or coil voltage on speaker output section of main) Likely dead main from FLIR image
          • All voltages present on PSU output to main
          • Main board has onboard 1v 1.5v 1.8v 3.3v 5v when plugged in
          • FLIR shows hot spot in middle of SOC
          • Pressing power on shows no FLIR image change so basically no activity on main SOC even though it has power.



          I have background in modern chip design. This main board has NO DRAM chips! so DRAM must be inside...
          08-05-2023, 12:10 PM
        • Loading...
        • No more items.
        Working...