60" Philips No Picture HV circuit for DPTV305

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • mpobanion
    Member
    • Dec 2009
    • 23

    #1

    60" Philips No Picture HV circuit for DPTV305

    Hi, members
    Dead Set
    I have a Philips 60” DPTV305. The Power supply is working fine after replacing Capacitor. I have Audio but no picture. I have 5v standby and standby at correct volts when PTV is off. 130v present at connector 1518 pin 9. Checked for HV at G2 focus screen block, only has about 2.5v when this should be 200v. I checked @ location pin 1 of each CRT board. The focus block is a sealed module and all connections are insulated with rubber I could not get HV reading. Amplifier Power / Protect Thermal/ Generator Fly back pins 1-7: These 1-10 pins are right under the Fly Back unit. Spec; pin 1 -in .7v ; pin 2 12.9v ; pin 3 fly back .03v. Pin 4 -13v. Pin 5 amp out -12.5v. Pin 6 vsup 13v. Pin 7 +in .6v

    Can anyone confirm that I have a bad Fly Back component? Is the power amp in back of the Fly Back? I wrote down readings on fly back but they do not match-up with ones above. Any suggestions would help very much, Thanks
  • Elektrolyt47uF
    New Member
    • Apr 2009
    • 1

    #2
    Re: 60" Philips No Picture HV circuit for DPTV305

    Check if you have 135V going to HV generator and check vertical IC if not working
    there will no be high voltage

    Comment

    Related Topics

    Collapse

    • PNI E.
      tcl u65x9006 back light on but no picture sounf ok after 40 50 secs
      by PNI E.
      hi guys, i need your help again...i have tcl u65x9006. while i was watching it become darker like when a movie ends, little by little the image disappear. now if i turn on i have back light on, after like 1 min i have also sound but no picuture. the back light is on i take off one at time the ldvs but nothing change always no picture. i tried to cover with a piece of paper the pin of ldvs i cover like 7 8 pins but nothing worked. the tv stay with no picture. there is a tcon board.i checked the voltage there on the fuse i have 11,8 volts. there is caps in shorts on the exit of the tcon i have...
      02-20-2025, 08:36 AM
    • madyoyo
      Philips 37pfl560: Yellow picture
      by madyoyo
      HI.

      I have a weird problem with an old Philips 37pfl560 TV i put out of storage: the picture have a noticeable yellow hue, and its not caused by the settings (did a factory reset). I've never seen this before. I will try to get a photo with a real camera, with my phone its hard to see because of automatic white balance, but in real live the whites are really yellow.

      Anyone have an idea of what can cause this? Can CCFL tubes get "warmer" with time? This tv have several analog inputs,so its nice for retrogaming....
      05-30-2025, 10:16 AM
    • dronerat
      Samsung UE48JU6400W - back light on, sound on, sometimes picture.
      by dronerat
      Hi Guys,

      This forum has been in great help to me, but I stumbled upon a strange problem with a salvaged Samsung TV that I am banging my head to troubleshoot.

      PSU: L48S6 FHS BN44-00807D
      T-Con: BN95-01937A
      Panel: CY-GJ048HGLVLH
      MB: NA (Currently as the TV is assembled and forgot to take picture)

      As I said earlier I have some issues with the TV I got from a friend of mine. The TV had no picture, but sound, back light and everything else was working fine.
      It was sent to an authorized service for repairs and returned with the...
      05-15-2020, 08:03 AM
    • charlesdutcher
      No picture issue in Philips Chassis FTL2.1
      by charlesdutcher
      Hello,
      My Plasma Philips 37inch chassis FTL2.1 does not show picture. It automatically goes into protection mode after 30 seconds (red led blinks at 3Hz)


      Is there someone having any symptom like this? How to fix it?

      Thanks in advance!​
      08-06-2024, 09:55 PM
    • groomit
      Philips 50PUS7363/12 Backlight but no picture
      by groomit
      Hi,
      I'm having trouble with above mentioned TV. Bought it defect.
      Picture was heavily compressed around the horizontal axis. Fiddeled and tried different things (mask clock lines, swap T-Con). But no difference.
      Then I identified a heating capacitor on the left hand Signal-PCB (?) below the display. Replaced it by hand soldering. Checked for shorts afterwards. But now the screen stays black.

      I can see backlight, but screen stays black.
      What I've tried:
      - Disconnect right side cable from T-Con -> same (backlight but no pic)
      - Disconnect left side...
      11-22-2024, 02:43 PM
    • Loading...
    • No more items.
    Working...