Panasonic TX-L55DT50B

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • PontyPCs
    Member
    • May 2016
    • 16
    • United Kingdom
    #1

    Panasonic TX-L55DT50B

    Hi Folks.
    Got This TV In A Boot Loop Panasonic TX-L55DT50B, Replaced The SPI Flash EEPROM Failed To Cure It, Does Anyone Have The NAND Dump File For This Please.
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • tranquility
      Onkyo TX-NR809 – no hdmi, DTS or NAND chip ? stuck at starting kernel
      by tranquility
      Hello,
      i want to repair an Onkyo TX-NR809 receiver.

      symptoms:
      on power on, display appears and i hear one click. enue functions is given.
      - no hdmi output
      - audio output not tested, but i think it is not there
      - usb sticks are not recognized

      if i read out the chips with display+standby button + tone+
      both dts show only ????

      chip is D830K013BZKB4

      things i have done:
      - reflow of the dts chip without taking off and reballing
      - changed the aluminium caps without the big one with 25v because i dont...
      08-25-2025, 01:04 AM
    • luis71
      PANASONIC TX-43HX580E VESTEL 17mb230 Boot Loop issue
      by luis71
      Hello,i have panasonic TX-43HX580E,I tried to enable 48 bit color,HDR10+ and ALLM and stuck at boot loop screen.I have modified edid.edid.

      I have backed up PQ,SPI,and Profile if anyone want

      Which usb_auto_update_??.txt can i use to dump firmware?

      I would be grateful if anyone could help me to find the firmware for USB recovery.


      ...
      11-05-2023, 06:31 AM
    • Takeatry
      Yet another Samsung QLED Boot Loop
      by Takeatry
      Samsung QLED QN50Q β€” purchased 2022 started experiencing a delay in the picture coming on in the morning less than 2 years later. Did not know the term boot loop at that time. As the loop delay ran into a few minutes did all the recommended troubleshooting, soft and hard reset, changing cables and outlet locations, no help. As the delay increased contacted Samsung tech group and allow them remote access the tv. Tech was moving too fast to see exactly what he was doing but this ultimately it was also no help. Lived with the delay until it stretched out over 6 hours. Pulled of off the back cover...
      2 Photos
      10-04-2024, 02:57 PM
    • mattpd
      PS5 EDM-031 - Pulsing BLOD - SSD NAND chips never heat up
      by mattpd
      PS5 died in the middle of a game and never would boot again. Pulsing BLOD stays on forever but never boots.

      No LM damage. UART gives a generic "APU not responding" error.

      Under thermal camera, the SSD NAND chips stay stone cold. The controller warms, but not the NAND. I have a good 2.5v and 1.8v around the NANDs...

      I don't have a ton of PS5 experience, but I assume that the NAND would need to warm at least a little bit in order to boot...

      So to those with experience, would you expect at least a little heat from the NAND during...
      09-02-2025, 09:42 AM
    • Andre Gilbert
      Panasonic TC-P55ST50 8 blinks then no blinks
      by Andre Gilbert
      Hello! yes I know there is already lots of information about this issue. I have a Panasonic TC-P55ST50 that originally displayed an 8-blink error code. Following the troubleshooting flowchart, I ended up replacing the SS board. However, even after replacing it, the issue persists. The TV turns on and stays on without displaying an image, and continuity is confirmed on all connectors. What am I missing hereπŸ€”?
      Ok Im a mechanical engineer ...but I thought I was able to follow a rather simple flowchart for electric troubleshooting πŸ˜‚.

      TV Model: Panasonic TC-P55ST50
      ...
      1 Photo
      11-20-2024, 08:52 PM
    • Loading...
    • No more items.
    Working...