Panasonic Viera TC-50PS14 - 1 blink fault

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • SadPanny
    New Member
    • Aug 2017
    • 3
    • Canada

    #1

    Panasonic Viera TC-50PS14 - 1 blink fault

    Hello and good afternoon,

    So my girlfriend has a Panasonic plasma and the picture is great. However over the last few months it's developed a problem with the power of the unit.
    Initially when pressing power on the remote sometimes the tv would power on. Other times the tv power light would just blink once every few seconds.
    Over the last few months it's progressively gotten worse to the point where we have to press and hold the power button on the tv and one in every 50 attempts turns the tv on. The remote only sends the tv into intermittent flashing and will never turn on the tv first try.
    Once the power light begins to 1 flash sequence we can attempt to manually turn on the tv and it's hit and miss when it works. Sometimes 5 minutes sometimes and hour with or without unplugging.

    It's definitely 1 flash code every 3 seconds. Any help is appreciated.. thanks in advance
  • Biruslapio
    Badcaps Veteran
    • Nov 2013
    • 552
    • Brasil

    #2
    Re: Panasonic Viera TC-50PS14 - 1 blink fault

    Blinking once every 3 seconds means unknown error or stand-by voltage problem,which can be your case,i bet on capacitors failing or connections going loose over time,you need to measure what voltages are beeing fed from the power supply(P board) to the main(A-board).
    50 attempts?you're persistent i tell you.

    Comment

    • SadPanny
      New Member
      • Aug 2017
      • 3
      • Canada

      #3
      Re: Panasonic Viera TC-50PS14 - 1 blink fault

      Any suggestions where to get schematics?

      Comment

      Related Topics

      Collapse

      • cloo
        Panasonic ZT60 plasma tv with strange behavior and 8 blink code
        by cloo
        I recently got my hands on a 60" Panasonic P60ZT60 plasma tv (european model) that has some strange issues along with an 8 blink code.
        It know this tv is getting old but it was once considered one of the best plasmas ever made, and i think it is still holds on to that even by todays standards.


        So, long story short. When i first got the tv it had a very bright washed out picture with very raised blacks in all picture modes and i couldn't find the cause in the picture setting menus.
        After doing a factory reset this problem was gone and the picture was back to...
        01-06-2025, 06:02 AM
      • Vebririon
        panasonic TX-P50V10E 6 blink led problem
        by Vebririon
        Hi everyone,

        I'm new here and trying to repair my Panasonic TX-P50V10E plasma TV, which is currently showing the 6 red blink error code.

        Just for context: I'm used to building PCs and installing modchips in old consoles, but this is my first time trying to fix a TV. I'm French, and while my English is okay, I'm using ChatGPT to help translate and clarify my messages as much as possible — so please forgive any odd phrasing.

        I'm also not very experienced with using a multimeter, but I'm very motivated and ready to follow instructions carefully and report...
        05-17-2025, 10:16 AM
      • Jacksoft
        Panasonic Viera TX-P46G10E 11 blink even after fan replacement
        by Jacksoft
        Hi all,
        I have here a Plasma TV TX-P46G10E that before had a problem where it had issues with 11 blinks (FAN SOS) BEFORE starting normally. After that it works for all day long.
        It had some bad cold solder and I remade them all. After I replaced a fan that was half-dead (no RMP signal from the respective pin, but ok with 9V).
        Now the TV power up instantly and works perfect... only without the backplate!
        If the backplate is placed on the TV shutsdown after about 10min and start blinking with the 11 blinks. If I shutdown and re-powerup it starts blinking after a bunch of...
        11-26-2023, 07:22 AM
      • howardc64
        Samsung QN75Q6FNA backlight no display, red LED blink 2x, fault in panel
        by howardc64
        • Prior owner tried a replacement main board. No difference.
        • Samsung 2x red blinking standby LED = panel fault
        • Jumpered FB_TRDY_1 (pin 1 CN1300 left. main tcon->left side buffer boards) and FB_TRDY_3 (pin 95 CN1301 right. main tcon->right side buffer boards) This allows testing individual T-Con (on main board) connection to panel on this Samsung. Found fault on left side (viewing from rear of TV)
        • Each side has 2 buffer boards, disconnected left side flex between 2 buffer boards. Fault is on the left most board.
        • Tape masking eventually isolated to CN1300 pin 15 (CKV4_GOA) Display
        ...
        07-19-2025, 10:54 PM
      • Rictech
        Panasonic SA-MAX770PU SMPSU board fault....
        by Rictech
        Hello everyone. 😀

        As per thread title, this unit has a serious SMPSU fault. It blows F1001, which is a 10A M205 in the phase from the mains input.
        Very first thing I tried, was simply replacing the fuse, but the replacement ceramic fuse blew immediately.

        Looking at the schematic for this PSU, I then removed what I thought was the next likely candidate: D1001 - the HV main bridge rectifier.
        This isolated the fault(no longer blows the main fuse), but does not point me to the actual fault.
        There are no devices that have exploded or otherwise show signs...
        08-26-2024, 01:05 AM
      • Loading...
      • No more items.
      Working...