LG 42PJ350 dead?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Infocore
    New Member
    • Jul 2017
    • 9
    • Bosnia and Herzegovina
    #1

    LG 42PJ350 dead?

    Hello guys

    So... as title says it's LG 42PJ350.
    First of all was that Tv went of, and refused to turn on. Only clicking noise every few sec. After couple of minutes no clicking noise, no light. Nothing!
    Back cover is up. 3 boards in front of me.
    Put DC in and cheking for voltage.
    Voltage on EAY board on upper left connector is 00.00 on every pin.
    http://led-tv.moscow/wp-content/uplo...1%82%D0%B2.png

    Think that f302(F2. 5A H 250V) fuse is blown because it shows me no conection betwen both sides of fuse.
    But before that No Power shoet there was only clicking noise.
    Think that voltage regulator is bad :/
    But dk how to check that shiet :/

    How to check diode of voltage regulator?
    And where to buy caps for this tv.
    Hope that someone will start this journey with me ��
    Last edited by Infocore; 07-20-2017, 02:03 AM.
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • Donny2derby
      LGOLED55B7V Clicking and dead screen.
      by Donny2derby
      Picked this up other week and when I originally looked at in the sellers house I got 3/4's of a working screen and some horizontal lines across the 1/4 of it which was dead/black.

      Just tried powering it up at home and now all I'm getting is a clicking and some very faint lines on 1/4 of the screen whilst the entirety of it is dead.

      When using the remote I get two red clicks on the standby. Not sure if this means anything or helps. The same when I use the manual power up.

      Help appreciated. I'm an electrician, I've fixed a few in the past so not a total...
      08-10-2023, 04:23 AM
    • NConstantinou
      HP Z840 workstation power supply clicking noise
      by NConstantinou
      No power
      i have the above ps which i change the TOP258eg ic.
      Now i have power but is clicking and voltages are flutuating. I change all capacitors, i test all mosfets and all are ok.
      i am wondering what is the value of R901! I am getting 0.5Ohms. Is that correct!
      the colours look like R,R,W or silver,G Bl.

      Thanks...
      12-25-2024, 02:24 AM
    • badcappo
      Dead Thinkpad E15, hissing noise from BQ25710
      by badcappo
      Hello there, got a Thinkpad E15 on the bench, almost no vital signs. Only things: Power button white LED flashes several times when USB-PD gets connected (number of flashes varies from three up to twelve times, sometimes no reaction at all). Battery charge indicator LED stays orange. Most interesting is hissing / whining sound from Battery Charge Controller IC BQ25710 on the keyboard side of the main pcb. Board fuses tested and intact, no shorts found so far. BQ25710 is also the only thing on the board to become warm in thermal image (below 70 °C). Thanks for any hint.
      03-09-2025, 08:23 AM
    • MegaZAC
      Onkyo TX-SR805 noise in one channel
      by MegaZAC
      Surprisingly enough, this receiver doesn't have the DSP chip issue. The HDMI board does not get hot, and sound over HDMI works fine.

      Regardless of the input, the right channel has noise that is clearly noticeable even on average volume level. The only cases when there's no noise is when VCR input is selected (some tracks on the board are damaged, maybe that's why), or if HDMI input is selected but nothing plugged into it. In all other cases, even when no input is connected I still have the noise.

      There's some logic behind it. As soon as I select an input I get only left...
      04-23-2025, 10:09 PM
    • Sisko
      Onkyo-593 No power and now clicking sound
      by Sisko
      Hi all!!

      Ok just got a Onkyo SKW-593 sub woofer that has no power person told me that it smoked and that his GF let the volume full when she powered off the amp and when he came to turn it on the sub played but then suddenly smoke was coming out, didn't say from where. So opened it up and saw a resistor made of metal (pic) but can't see any writing on metal par so what ever was written on it was burnt. So I'm kinda stuck here with this. I did ask for a repair or schematics in the other group section and waiting for this but I hope someone here might lend me a hand to try and identify...
      Schem
      4 Photos
      Today, 02:18 PM
    • Loading...
    • No more items.
    Working...