PANA TNPH0800 repair

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • ajshoe
    ajshoe
    • Dec 2012
    • 477
    • usa

    #1

    PANA TNPH0800 repair

    Have a Panasonic TC-P42X1 plasma with bad A Board TXN/A1EQUUS. I see EBAY has "repair service" for these boards. Does anyone have a clue as to what goes bad on these boards ?? Is there a common repair for them ?? thanks
  • tom66
    EVs Rule
    • Apr 2011
    • 32560
    • UK

    #2
    Re: PANA TNPH0800 repair

    10 blink code?
    Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
    For service manual, schematic, boardview (board view), datasheet, cad - use our search.

    Comment

    Related Topics

    Collapse

    • Ancient1
      I have no clue how-to : TV auto-starts with Android no buttons and LED fast flicker
      by Ancient1
      CROWN Smart TV, 50", Single board design

      1. TV starts with Wall power..
      2. The front LED is blinking very fast that it looks like a red&green LED
      3. The Android Menu in the photo appears
      4. Buttons are not responsive

      I tried few pre_Power Button Combos, and with Power, but none worked

      I'm scratching my head how to start diagnosing.. ??...
      10-19-2022, 10:12 AM
    • marivox
      Samsung Eco Bubble VRT plus 12.0 kg
      by marivox
      Masina de spalat ,are aprox 7 ani,a functionat perfect pana acum .De o saptamana insa ,sare programul de stoarcere.Am curatat filtrul pompei de apa,am verificat daca paleta pompei de apa se invarte usor,daca rezistenta de incalzire este in regula,daca evacuarea apei din cuva se face corespunzator.Toate sunt in regula.Am selectat programul '''Rinse+Spin cu durata de 18 min.Masina a functionat corect pana in min 9,sarind la min 1 ,oprindu se dupa aceea,deci sarind peste programul de stoarcere.Va rog ,date cele relatate ce este de facut.? Banuiesc ca ar putea fi softul corupt si ce ar fi de facut...
      11-28-2024, 01:25 PM
    • Cory Meyers
      🤯 Acer Predator Helios 300 pH315-54
      by Cory Meyers
      Hi there all, 1st post here. I wasn't aware there were guys out there doing this for people! (how, well I haven't a clue lol but 😎👍 badass!), So when I found y'all, I was happy, but not too happy quite yet - although my issue seems to be less severe than many I've seen here who have been happily helped, so there's that.

      I'm a software dev of over 20 years and just recently have gotten into the hardware side of things plus other electronics like Rpi and Arduino. Started off a vid game hacker yada yada, same story. Lol.

      Now, the BIG OL' issue ruining me little life:...
      10-28-2024, 05:11 PM
    • Exim
      Asus M2A-VM preventive KZG recap, as it turned out unnecessary in this case
      by Exim
      This Asus M2A-VM was running 24/7 for 12 years without problems. CPU was a TDP 45W DualCore only, but still, 12 years are 12 years. I'm preparing this board as a spare part, it has to replace another one with blown caps. So before using it as a spare part it obviously needs to be checked. Because of the collection of bad caps usually on this board I was prepared for the worst.

      Surprise #1: This particular board is an "almost-exclusively-Panasonic" specimen. It has the usual four 1000/16 Chemi-Con KZG plus three Chemi-Con KMA. Instead of the usual single Sanyo WX there's...
      11-08-2020, 05:41 PM
    • davidebeatrici
      UMA conversion LA-4982P (Toshiba Satellite Pro L500 series)
      by davidebeatrici
      Hello,

      I have two almost identical computers, unfortunately both with a faulty MXM graphics card. More specifically:

      - One doesn't enable the backlight and exhibits artifacts in the form of colored stripes, with the drivers crashing immediately with a BSoD upon loading.
      - One was exhibiting very similar if not identical artifacts and then the GPU became fully shorted, right after a reflow attempt.

      Since the LA-4982P was also manufactured without the MXM slot (pads unpopulated), I immediately thought about performing a UMA conversion. Unfortunately there...
      06-09-2025, 01:15 AM
    • Loading...
    • No more items.
    Working...