Changing power supply caps 'just because'?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Nicholas
    Senior Member
    • Dec 2014
    • 60
    • Kingdom of Denmark

    #1

    Changing power supply caps 'just because'?

    Hi guys

    I have a Panny 50" plasma from 2010 that I just changed the main board,
    works great now. These models(I hear) have the problem of occasional
    flickering in the brightness and sometimes grainy blacks. Yes, AGC and CATS off

    Well, my question is. The set has no fans. Before I install it in its main place,
    should I just change the caps on the power supply? They look like no-name,
    and I have plenty of good caps. The set is 4-5 years old now, soooo would
    it be a good idea?

    Thanks,

    Nicholas
  • tom66
    EVs Rule
    • Apr 2011
    • 32560
    • UK

    #2
    Re: Changing power supply caps 'just because'?

    I'd leave the originals in. Panasonic are well built and rarely encounter issues with their electrolytic capacitors. A fan might be a good idea though.
    Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
    For service manual, schematic, boardview (board view), datasheet, cad - use our search.

    Comment

    Related Topics

    Collapse

    • Tynan Dill
      Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
      by Tynan Dill
      I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

      Upon bringing it home and plugging it up, it showed a standby light.

      I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

      The screen seems to blackout and stay black, but with a flashlight I can see the display.

      With my Playstation 4 connected via HDMI, and running a game I can hear sound.

      Assuming...
      11-22-2024, 01:46 PM
    • eryjus
      Heathkit IO-4205 Power Supply Caps
      by eryjus
      Hello,

      First, I am a complete noob with high voltage stuff. I'm learning, but I need help by someone looking over my shoulder.

      I recently came into posession of a Heathkit IO-4205 5MHz Dual Trace Oscilloscope. The documentation is copyright 1978. I'm told it works.

      I opened it up to check the caps before I applied power, and found the following black caps and wanted to know what they were. They are on the power supply board. I was able to read the name and model and came up with, "Nytronics 162J-1, 0.1uF, 20% tolerance, 2000VDC."
      ...
      05-10-2023, 11:21 AM
    • captain150
      Help with switching power supply caps
      by captain150
      I'm trying to repair two old VCRs, they both have bad caps. One has leaky ones, the other would barely run until I subbed in some caps from another power supply I had laying around (though they are the wrong values). This vcr works for an hour or two, but then the power supply starts whining and the picture gets lines in it. I didn't replace all the secondary caps, so another voltage might still be problematic, or the values I used are too far off.
      I've been on mouser and digikey but the options are a bit overwhelming. I just need some new ones that will work. They don't need to be top quality,...
      03-16-2025, 07:34 PM
    • sam_sam_sam
      Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
      by sam_sam_sam
      I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

      One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
      03-31-2024, 02:12 PM
    • sam_sam_sam
      Modification to a ZD-987 desoldering/soldering station using a external switching power supply
      by sam_sam_sam
      I have been working on this concept for quite some time now with limited success but recently I found a switching power supply that is setup for the voltage that this soldering station needs to operate at however it also needs part of the secondary circuit from the original switching power because you need several voltage rails

      I once tried to get a ZD-915 desoldering station to work on a 18 volt battery power supply but unfortunately things did not go well but I did find a work around but I might try this idea again but going at a little differently more about this another time...
      07-01-2024, 06:34 AM
    • Loading...
    • No more items.
    Working...