Replaced Panasonic Kit on SC board ans Q102 (Mosfet-N shorted) on SS board.
-
-
Re: Panasonic TX-P50GT30E 8 blinks (solved)
thanks for the tip. Also make sure that the screws that hold the board to the panel are nice and tight and don't have any dark marks on them this is one main reason why it shorts the board outDid I leave the soldering iron on? -
Re: Panasonic TX-P50GT30E 8 blinks (solved)
Hi All,
sorry for my english, i have the same tv like the same issue (8 Blinking led).
In the first time my tv had 7 blinking led, i checked the SC card and i found the short in the transistors.
I have changed with kit for SC card the DUT broken and the now my tv has a 8 blinking led.
I saw the VSUS voltage and i noted 200V this is too small because in the schematic the VSUS is 220V.
If I remove the SS card (TNPA5331) and the SS33 flat the led TV is green but the display is black.
I suspect the issue is the SS Card but i have verified the diodes and the all MOS and i dont found any Short .
Please i need your help for found the DUT broken.
You can help me?
Very ThanksComment
-
Re: Panasonic TX-P50GT30E 8 blinks (solved)
I had the same issue. 7 blink shorted SC, then went 8 blink after repair and it was bad SS Q102 for me. Everything connected right including the SC20 ribbon?Attached FilesComment
-
-
Re: Panasonic TX-P50GT30E 8 blinks (solved)
Neither do I . if you can't find the part you might have to try another SS boardComment
-
Re: Panasonic TX-P50GT30E 8 blinks
Hi,
how i can test the MIP391 DIP7 PANASONIC?
ThanksComment
-
Hello! yes I know there is already lots of information about this issue. I have a Panasonic TC-P55ST50 that originally displayed an 8-blink error code. Following the troubleshooting flowchart, I ended up replacing the SS board. However, even after replacing it, the issue persists. The TV turns on and stays on without displaying an image, and continuity is confirmed on all connectors. What am I missing hereπ€?
Ok Im a mechanical engineer ...but I thought I was able to follow a rather simple flowchart for electric troubleshooting π.
TV Model: Panasonic TC-P55ST50
...11-20-2024, 08:52 PM -
Bought this TV used not working, panel flashed briefly on power up and it was blinking 8 times, a quick look on SS board revealed a common fault on the 3uF 250V capacitors, C201 to C205 (C1620X in the service manual), the solder joints were all cracked, C201 and C205 pins were darkened and some sparking had occurred on them, C201 was split open and clearly overheated in its last hours, replaced that one and resoldered the others, 8 blinks fixed.
Also the previous owner broke the antenna connector by taking the TV out of the wall mount forgetting to unplug it, I desoldered the tuner... -
Hi,
anyone able to provide the service manual for old plasma Panasonic TX-P42ST50E?
It turns off almost immediately (0~5 seconds after pressing the on/off button) and starts flashing the red diode 6 times.
I disconnected the left-hand side board (SC?, both the ribbon cable and the power cable to it) and also another ribbon going to bottom left board. Then the led signal is 8 flashes. According to service guide to another Panasonic plasma it would mean the left-hand side board is faulty. But I'm not sure it 100% applies to my model.
I checked that board for any obvious faults... -
Hello,
Stopped by this site trying to fix my parents Panasonic Plasma TV.
Model number is TH-50PZ85U
Power comes on and the red power light stays on solid.
Did a few checks like hold the power button on for 60 seconds, hold the - Volume while holding the menu button, no luck, still@ blank grey screen as the screen lights up very vague.
I also hear a few clicks.
I also think my parents said there was a thunderstorm and the TV failed after that.
Section 6 in the service manual talks about power and no screen,...10-30-2024, 10:09 AM -
Hello all,
As the title states, I followed the troubleshooting guide located here: https://www.manualslib.com/manual/23...page=53#manual, which concluded the 'A' board needs to be replaced. Looking around the net and eBay, I see that there are repair services for the board (TNPH1043UE? Not sure if it is a 'UE' as the suffix grid does not appear marked). What additional troubleshooting can be performed to ensure 1) this board is the problem and 2) since there are repair services, what are they fixing on the board?) I expected 3.3V not to be available anywhere...
Comment