NEC PX50XM4W panel main input board required

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Greg32
    New Member
    • Aug 2014
    • 5
    • Australia
    #1

    NEC PX50XM4W panel main input board required

    Hi all, great forum ive been able to fix a Samsung with a bung xsus board with info from here, thanks.
    What Ive got is my own 50" nec that has developed an issue with the component inputs, it displays vertical rainbow pattern when these inputs are used/selected ,I have done a reset with no improvement. If I use the dvi input all is perfect and the picture is A1.
    Am I right in thinking that the main input board is the culprit ? ive included a couple of pictures. so I think im looking for a replacement input board if any one can advise on this I would be much appreciative. Thanks Greg
    Attached Files
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • howardc64
      TCL 55S425 few horizontal lines, potential failure on both side of panel/buffer board
      by howardc64
      All left and right refers to looking from rear of TV (or looking from front with TV upside down)
      • TV came with vertical bars and no image. Found faulty TVS on left buffer board. Also replaced T-Con (may have damaged the original while hot air removing components, board has slight warp) and have full image but few horizontal lines on the screen. Some of the lines appears to be 2 pixel tall while others are 1 pixel tall.
      • Disconnecting left and right buffer board potentially reveals problems on both sides with different signals (unless this T-Con require jumper like Samsung FB_TRDY1&3) Fault
      ...
      07-24-2025, 05:17 PM
    • jb_Bak
      Sony xbr-65x900c main board issues?
      by jb_Bak
      Hey guys great forum glad to have found it. I bought a Sony XBR 65X900C cheaply because it didn't work. No signs of life at all not even a light/led. All I hear is a brief high voltage sound when I throw the power to it.

      Didn't see any obvious signs of damage so right away started checking voltages. This is what I see:
      Power Board Connector that goes to Main board
      CN6401
      Pin 01 NC
      Pin 02 NC
      Pin 03 "BL_ON": 0V
      Pin 04 "N/C"
      Pin 05 "STBY 3.3V": 3.5V
      Pin 06 "GND": N/C
      Pin 07 "AC_OFF"...
      09-27-2021, 04:52 PM
    • JDC
      (SOLVED) - ONN 100012588 No Power, Then Rebooting After Main Board Change
      by JDC
      ONN 100012588
      Issue: No Power, Then Rebooting After Main Board Change

      Short answer: replace main board and power board
      Technical answer: replace main board and Q306 & Q307 on power board.

      Long answer:

      TV wouldn't turn on. Power switch was fine which means the main board isn't processing the power on signal. Replaced main board. TV turns on now but randomly reboots. Bad main board? EEPROM? Tried to pull main board and got a shock touching the corner of the board. That's weird. C334 (450V 10uf) capacitor is still holding a high charge....
      07-15-2022, 07:39 AM
    • m1ch43lzm
      HP Pavilion 15-eh Board DAG7HAMB8F0 - CPU throttling to 0.4GHz (PROCHOT_EXT) and black screen
      by m1ch43lzm
      Hi, this is my personal laptop, which the original board (lets call it Board A) blew up PU8700 (TPS51486), making a hole on the board, i had left the laptop at my desk one day with the battery fully charged and didn't touch it for a week, but when i tried to turn it on it didn't
      Thought the battery was dead, so i plugged in the charger then tried to power on, the power LED blinked once, charged LED still orange, unplugged the charger, plugged in again and I noticed the "magic smoke" smell, so i unplugged the charger, removed the back cover and saw the blown IC (the "magic...
      05-12-2025, 08:37 PM
    • cheeky2
      Is it possible to upgrade from a Vestel 17MB97 main board to a 17MB110 Main board?
      by cheeky2
      I suppose the real question is whether the existing pinouts from ether a 17IPS71 psu are cross compatible with a 17IPS12 psu? If they are then the exchange of the main boards should have no issues providing the screen is compatible with both main boards. Obviously you can change the screen configurations easily enough (providing you have the correct files) for the main board. Why may you ask would I do this? Well a lot of the smart features are no longer working on a Hitachi 48HBT62U main board I wish to give it a new lease of life!
      Obviously the same LVDS connector for the screen connection...
      05-25-2024, 03:27 AM
    • Loading...
    • No more items.
    Working...