lg 50pa650t no picture

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • tom66
    EVs Rule
    • Apr 2011
    • 32560
    • UK

    #21
    Re: lg 50pa650t no picture

    On these, it will almost certainly be a bad panel as this frequently occurs - I can recall 10 with the same fault on this forum and one I did myself.
    Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
    For service manual, schematic, boardview (board view), datasheet, cad - use our search.

    Comment

    Related Topics

    Collapse

    • maneatingmonkey
      Missing LCD Panel Voltages VGH, VGL, VCOM (TCL 55P6US Sound & Backlight but NO Picture)
      by maneatingmonkey
      I have a TCL 55P6US with sound and backlight but no picture. This model does not have a T-CON board, and the right (rear perspective) panel board is fed from the left panel board. I have not been able to induce any change by disconnecting the secondary panel board or the tape cut-off method on the primary board.

      There are a bunch of voltages missing on the panel boards. I can't find any shorted caps of the panel boards, and all of the missing voltage rails read in the kiloohms, which leads me to suspect the issue may lie on the circuit board, rather than a short in the panel.
      ...
      03-27-2024, 07:17 AM
    • Tr0ll
      T-con suspect issue. Both ribbon cables no picture. One ribbon cable ok. (58pus8545)
      by Tr0ll
      Hi guys! I realized you have a lot of knowledge here so i am hoping you could point me in right direction with my odd issue.

      The Tv is a Philips 58PUS8545/12, it had no picture but working backlights.

      Original T-con:
      Opened the Tv and tested to unplug one ribbon cable at a time. With this test i could see that i got fine picture on both halves as long as there was only one ribbon cable connected, with two connected picture were gone.

      First replacement T-con:

      I thought it might be t-con and ordered new t-con from china(supposedly tested)...
      10-07-2023, 07:48 PM
    • JJAAMM
      SAMSUNG UN55KS9000F picture fades then distorts into vertical lines after 20 seconds
      by JJAAMM
      This was my main TV for the last 6 years. I'm not inclined to throw out a $2600 TV so quickly so I'm trying to investigate the issue.

      Problem
      TV was disconnected from power for 6 months during construction. When I plugged it yesterday picture was fine, after 30 seconds it dimmed then started developing horizontal lines, picture then starts to ghost vertically until it degrades into vertical streaks. TV always displays a perfect picture when cold. I can unplug TV for 5 minutes and plug it back in and picture is restored for 20 seconds. I can also keep it in standby mode...
      07-06-2023, 06:01 AM
    • TR103
      Samsung TV model UE50TU: rebooting, backlight, sound, but no picture
      by TR103
      Hi, I have a Samsung UE50TU with:
      - sound and backlight, but no picture
      - when it arrived, it had a picture for a few seconds
      - it keeps rebooting
      - without ribbon cable between the two panel boards, it does not reboot but I have no picture
      - without cable between mainboard and lcd panel, it does not reboot (but obviously i have no picture)
      - when i try a tape fix, its keeps rebooting, unless I tape off pin 1 (the innermost pin). In that case it does not reboot but I have no picture.

      - without cable between mainboard and lcd panel and with a jumpered...
      01-22-2025, 04:12 PM
    • howardc64
      A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
      by howardc64
      Problem

      This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
      08-04-2024, 10:36 PM
    • Loading...
    • No more items.
    Working...