Lg 50pc 3d aa

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Dino61
    New Member
    • Aug 2013
    • 3
    • Australia
    #1

    Lg 50pc 3d aa

    Hi, TV had the vertical bar problem, but after a couple of times turning it on and off, now nothing at all, no sound or picture. I read a bit, but not enough! and replaced the power board but its still the same.... reading more on here it could be the buffer boards and I should test for resistance ? Got them hanging on the ribbons, but which way do the little clips pull?

    I did disconnect the left and right hand boards and turn it on aagin, but no difference, same with bottom buffer board and both disconnected...
    Last edited by Dino61; 08-21-2013, 10:01 PM. Reason: advanced a bit
    Tags: None
    • capkid
      Badcaps Legend
      • Oct 2010
      • 1339
      • United States
      #2
      Re: Lg 50pc 3d aa

      Can you post a pic of that area?
      LG Plasma Mal-Discharge Correction Service

        Comment

        • Dino61
          New Member
          • Aug 2013
          • 3
          • Australia
          #3
          Re: Lg 50pc 3d aa

          aah just put it back together to shift it out of the lounge...will do next day or so...thanks for the reply

            Comment

            Previous template Next

            Related Topics

            Collapse
            • howardc64
              A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
              by howardc64
              Problem

              This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
              08-04-2024, 10:36 PM
            • Yanleb
              Schematic or datasheet for Plasma TV buffer chip
              by Yanleb
              Hi all,

              I'm interested in understanding how a buffer board chip is working. I know there's about 90 outputs per chip to the plasma panel, but I'm more interested to know about the input pins. I guess that some of them are address pins, but I want to know more.

              So far I've found nothing at all. I haven't found any datasheet about the various buffer chips, and I haven't found any schematic for the buffer board using them (Y Buffer Board in Samsung's terminology).

              Any information will make me happy. It can be from any buffer chip or plasma TV manufacturer....
              05-18-2022, 01:36 PM
            • legg
              LG 42PC3 buffer output doesn't follow YSUS
              by legg
              LG42PC3D -UD originally with green lamp but no display or audio.
              Owner says was working, then went 'pop'.
              All 5V caps bulging. replaced.
              All PSU output voltages within spec but -Vy is low on YSUS.
              One of three parallel fets between SUS_OUT and SUS_DN is zenering,
              eventually shorts DG. Replaced all 3 - -Vy now OK.

              Y scan buffer test point does not follow YSUS output below -50V

              Note: This unit seems to expect YSUS output to park at -Vy in between
              drive signal pattern periods. A replacement drive signal board confirms this....
              11-18-2021, 11:49 AM
            • reformatt
              Windows 11 Start menu/Taskbar hanging
              by reformatt
              Couple of Windows 11 machines have come in this week with the same issue. After you login, the taskbar will not appear (or just be a black bar). No access to Start Menu. Task Manager (use CTL+SHIFT+ESC) works, however the Performance stats seem stuck with CPU on 100% for Task Manager itself. Trying to exit Task Manager result in it hanging as well. No issue if you boot into Safe Mode.

              First machine, tried many things to no avail (System Restore from last Windows update, rebooting in Diag mode, trying to reinstall Windows Apps via Powershell). In the end, I did an in-place upgrade...
              04-23-2024, 10:16 PM
            • howardc64
              Samsung QN75Q6FNA backlight no display, red LED blink 2x, fault in panel
              by howardc64
              • Prior owner tried a replacement main board. No difference.
              • Samsung 2x red blinking standby LED = panel fault
              • Jumpered FB_TRDY_1 (pin 1 CN1300 left. main tcon->left side buffer boards) and FB_TRDY_3 (pin 95 CN1301 right. main tcon->right side buffer boards) This allows testing individual T-Con (on main board) connection to panel on this Samsung. Found fault on left side (viewing from rear of TV)
              • Each side has 2 buffer boards, disconnected left side flex between 2 buffer boards. Fault is on the left most board.
              • Tape masking eventually isolated to CN1300 pin 15 (CKV4_GOA) Display
              ...
              07-19-2025, 10:54 PM
            • Loading...
            • No more items.
            Working...