qn55qn85aaf schematic

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • itelite
    Senior Member
    • Aug 2016
    • 124
    • USA

    #1

    qn55qn85aaf schematic

    bn41-02855d Main board

    Feels like a long shot, but any one have the schematic for the main board?

    It seems to have a panel short that i cannot find. It feels like it is doing the VGH reboot thing that a few other series of samsung do, but i cannot conclusively locate the VHG pin/line.


    It will cycle/reboot forever unless i unplug the ribbon between the panel PCBs. If i plug that ribbon back in while running it will shutdown and begin the cycling with in a few seconds.

    Checked every passive on the panel for shorts and got nothing interesting. I can probably screw round with tape to find what pin is causing it, but ive had a lot of luck with samsungs in the past with increasing the value of the series resistor on the VGH line, and would like to give that a try.

Related Topics

Collapse

  • zesko
    xps 9520 ribbon cable
    by zesko
    Hello,
    I have a XPS 9520 with broken daughter board and missing ribbon cable. I can fix the board by replacing the connector, but I can't find the correct ribbon.

    There is 2 models, idk which one is needed on my laptop.

    0xkvng
    00vpr2

    Daughter board is LS H822P. When I check for a palmrest, the board attached to have a 0xkvng ribbon. But when I check for LS h822p, it's 00vpr2 ribbon...

    Someone can help me with that please ? Idk the difference between these 2 ribbon but they definitely doesn't look the same..

    thanks...
    10-23-2025, 05:03 PM
  • Tr0ll
    T-con suspect issue. Both ribbon cables no picture. One ribbon cable ok. (58pus8545)
    by Tr0ll
    Hi guys! I realized you have a lot of knowledge here so i am hoping you could point me in right direction with my odd issue.

    The Tv is a Philips 58PUS8545/12, it had no picture but working backlights.

    Original T-con:
    Opened the Tv and tested to unplug one ribbon cable at a time. With this test i could see that i got fine picture on both halves as long as there was only one ribbon cable connected, with two connected picture were gone.

    First replacement T-con:

    I thought it might be t-con and ordered new t-con from china(supposedly tested)...
    10-07-2023, 07:48 PM
  • TinkerTron
    Schematic vs. Reality: Where Are the Resistors on My Sharp Clock Radio? Model FY-70CH
    by TinkerTron
    Hey everyone,

    I'm currently working on a mid-70s Sharp Electronic Digital Clock Radio, Model FY-70CH. I found the service manual online, printed it out, and have been studying it for a while. My main reasons for tackling this are: (1) I want to learn electronics and figured I'd start with something I had on hand, and (2) I want to fix its issues. Right now, the radio sounds awful, has about 5V DC at the speaker terminals, and the alarm time setting doesn't work. But I'm not asking how to fix these problems.

    Instead, here's what's been bugging me so far:
    The schematic...
    03-06-2025, 02:03 PM
  • atunguyd
    Acer x163w Monitor PSU schematic
    by atunguyd
    Ii wonder if anyone can help me. I have a Acer x163w monitor which is not powering up. The PSU main capacitor's one leg had completly come off - I replaced it but the PSU is still not outputting DC. I found the monitor in questions service manual here on manuals lib but the schematic in there is a completely different - the schematic shows no mosfet to drive the transformer while the one I have does use a mosfet - also the schematic shows only one optocoupler but mine has two.
    The PSU board is labelled FM-20A02-AAA made by APD as per the image below. I am trying to find a schematic for this...
    03-05-2025, 02:08 PM
  • gretti
    MSI Z370-A Pro, works but does not power off or reboot and USB issues
    by gretti
    I have a MSI Z370-A Pro. The board does not reboot or shut down from the Windows recovery console. USB communications stop and the status light on USB 1 stays on and does not blink. I have programmed a new BIOS with a CH341A programmer already, swapped RAM, PSU, CPU. The board will power off when the power button is held and resets when the reset switch is pressed, but it will not react to the reset switch if already told by software to shut down or restart. The board will reboot from BIOS after a save and exit command.

    The MSI BIOS included the ME firmware for the board. The size...
    10-16-2025, 02:14 AM
  • Loading...
  • No more items.
Working...