Samsung "MU" series (UN, UA, UExxMUxxxx) fault dump IC1604 25Q40...

[lotas]

Do you use it through a clamp or do you unsolder the flash and use an adapter on the programmer?
Try another flash...

[yureyko]

I was experimenting with everything back then... Now all the settings are correct.

[lotas]

I tried your firmware, but I have the same problem. I have a black CH341A.

When I try your other firmware for different TV models, I still have the same problem. It's probably an issue with the programmer or the SPI chip.

And in the settings it is set as green.

[yureyko]

Try this dump.
And is your CH341A black or green?

I tried your firmware, but I have the same problem. I have a black CH341A.

When I try your other firmware for different TV models, I still have the same problem. It's probably an issue with the programmer or the SPI chip.

[yureyko]

Try to remove protection first, i.e. remove all checkboxes and press "Write", then erase and write dump again, then set the status register again...

The same behavior in three programs (SiberiaProg, Colibri, NeoProgrammer).

[lotas]

Try this dump.
And is your CH341A black or green?

[yureyko]

The same result, it immediately enables that parameter.

[lotas]

Try to remove protection first, i.e. remove all checkboxes and press "Write", then erase and write dump again, then set the status register again...

[yureyko]

Maybe I have a problem with the SPI chip or the CH314A programmer. Mine is not modified. Do I necessarily need to modify it?

[yureyko]

There should be only (S3, S7, S9, S14).
Try to record your native dump again via NeoProgrammer_2.2.0.10.

In the program:
1. Click "Detect Chip" and select W25Q40CL and "Select IC".
2. Click "Unprotect".
3. Click "Clear IC" and "Yes".
4. Click "Open File" and select your corrected dump.
5. Press "Program IC" and "Yes".
6. Click "Verify IC".
7. Press the down arrow to the right of "Unprotect" and select "SREG Edit", put a check mark on SRP0, BP1, CMP, QE (S3, S7, S9, S14) and press "Write" and "Yes"
7. Close the program. Ready.

Dear lotas ,
I already have some default parameter set. That's why I can't set the register code 0x42.

[lotas]

There should be only (S3, S7, S9, S14).
Try to record your native dump again via NeoProgrammer_2.2.0.10.

In the program:
1. Click "Detect Chip" and select W25Q40CL and "Select IC".
2. Click "Unprotect".
3. Click "Clear IC" and "Yes".
4. Click "Open File" and select your corrected dump.
5. Press "Program IC" and "Yes".
6. Click "Verify IC".
7. Press the down arrow to the right of "Unprotect" and select "SREG Edit", put a check mark on SRP0, BP1, CMP, QE (S3, S7, S9, S14) and press "Write" and "Yes"
7. Close the program. Ready.

[yureyko]

Then check what status register is set, maybe it has crashed (it should be 0x88, 0x42).

Dear lotas ,
After installation in the TV, the status changed to 0x46.

[yureyko]

Then check what status register is set, maybe it has crashed (it should be 0x88, 0x42).

[lotas]

Interesting...
All voltages are present, but the indicator does not light up.
However, when I try to flash the SPI with a working firmware from a similar model, the indicator lights up, but there is no startup...

Then check what status register is set, maybe it has crashed (it should be 0x88, 0x42).

[yureyko]

Your dump is working, the problem is different...

Interesting...
All voltages are present, but the indicator does not light up.
However, when I try to flash the SPI with a working firmware from a similar model, the indicator lights up, but there is no startup...

[SMDFlea]

The thread title has been renamed to Samsung "MU" series (UN, UA, UExxMUxxxx) fault dump IC1604 25Q40...

[lotas]

Greetings friends,

i have a Samsung TV UE40MU6402U with board BN41-02568b
The problem is that i have no standby
I thint that maybe the problem is software related since i have voltages in board.
I read the IC1604 (W25Q40CL)
Propably problem is the IC1604 but i read all of them.
If someone knows or have software to help please you are welcome.

Thanks in advance for your time and your help.

Your dump is working, the problem is different...

[yureyko]

Greetings friends,

i have a Samsung TV UE40MU6402U with board BN41-02568b
The problem is that i have no standby
I thint that maybe the problem is software related since i have voltages in board.
I read the IC1604 (W25Q40CL)
Propably problem is the IC1604 but i read all of them.
If someone knows or have software to help please you are welcome.

Thanks in advance for your time and your help.

[lotas]

Thanks Iotas. It works fine!

Ok!

[ducky29]

Hi, try the working dump.

Thanks Iotas. It works fine!