B&W Zeppelin Power Supply - ALP0050-0000

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • rtk74
    New Member
    • Oct 2017
    • 2
    • Australiea
    #1

    B&W Zeppelin Power Supply - ALP0050-0000

    Hi guys, first time poster and I need some help with some wiring.
    Right now I have this Power Supply from a B&W speaker.
    Not working and in need for some caps since the ones mounted were some unknown Chinese brand.

    Wanted to know the ground for the power supply since I'll be installing a CSR8645 12v for bluetooth connection. I'll be using a L7812 regulator for powering it up.

    http://cdn-docs.av-iq.com/dataSheet/...050-series.pdf

    The link is for the schematics. They're the only ones I could find.

    https://www.badcaps.net/forum/showth...id=8&styleid=7

    https://www.badcaps.net/forum/showth...ighlight=B%26W

    Some of the photos of the board are in these pages. Sorry for not uploading my own since I have a potato camera and I don't want to steal any photos.
    Thanks for taking your time to read this.
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • Tynan Dill
      Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
      by Tynan Dill
      I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

      Upon bringing it home and plugging it up, it showed a standby light.

      I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

      The screen seems to blackout and stay black, but with a flashlight I can see the display.

      With my Playstation 4 connected via HDMI, and running a game I can hear sound.

      Assuming...
      ORIGINAL POWER SUPPLY BOARD
      7 Photos
      11-22-2024, 01:46 PM
    • sam_sam_sam
      Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
      by sam_sam_sam
      I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

      One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
      03-31-2024, 02:12 PM
    • sam_sam_sam
      Modification to a ZD-987 desoldering/soldering station using a external switching power supply
      by sam_sam_sam
      I have been working on this concept for quite some time now with limited success but recently I found a switching power supply that is setup for the voltage that this soldering station needs to operate at however it also needs part of the secondary circuit from the original switching power because you need several voltage rails

      I once tried to get a ZD-915 desoldering station to work on a 18 volt battery power supply but unfortunately things did not go well but I did find a work around but I might try this idea again but going at a little differently more about this another time...
      07-01-2024, 06:34 AM
    • shamsudeen
      Hi, Can we use SMPS Bench Power Supply for Laptop troubleshooting?
      by shamsudeen
      Hi all, I just need to know that, can i use SMPS type power supply to test and short circuit detection on a laptop motherboard?
      I saw 95% of repair guys are using only Linear bench power supply. linear bench power supply is pricy, thats why i planned to get one SMPS supply.

      i know that in linear power supply the noise will be very low comparing to SMPS supply....
      07-19-2025, 07:14 AM
    • CMCM
      Russound CA4 Power Supply Repair
      by CMCM
      Hello Everybody,

      Trying to repair a power supply from a Russound CA4 Multizone Controller (picture attached)

      Russound no longer supports it but were kind enough to provide a schematic of the power supply (pdf attached).

      The outputs marked 12v and 20v are all measuring only 1v.

      The board is clicking, which I think means it is in something called hiccup mode when the flyback transformers switches because of an internal problem or something else on the board Overloading it.

      The capacitors physically look clean (no bludgesor leaks) and...
      07-03-2025, 01:12 PM
    • Loading...
    • No more items.
    Working...