Sony AZ series HCR-AZ5D Power Issue

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • DjKrish
    Badcaps Veteran
    • Oct 2012
    • 354
    • SG
    #1

    Sony AZ series HCR-AZ5D Power Issue

    Ok i have this set for sometime now and suddenly there's problem with power. The red standby light is working, but when u press it to on the unit, its like the set is on low battery. If u press the power button again, the light comes back to red standby. If u don't press the button back again, then the red light starts flashing. Is there a problem with the power supply? Less power supplied to the main board? Faulty power supply? Theres no display either. Only the power red light works. I thought it was cold solder joints, i re soldered everything, still same. TO check the power supply voltages, i dont have the diagram either Can anyone help pleaseeee.....
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • cajoeg
      Insignia NS-LCD019-09 issue: Power light turns blue for 3 seconds, the flashes red before going solid read again
      by cajoeg
      Hello, I'm new to the group and to trying to repair a LCD TV. During the past few years, I've been collecting/repairing/restoring vintage personal computers (Commodore, Apple II, Atari, TRS-80, Texas Instruments, and Timex Sinclair). This has been my retirement hobby. Now I've gotten interested in trying to repair a LCD TV that I have and used regularly when working on vintage computers.

      The LCD I'm working on is a Insignia NS-LCD019. I've downloaded the service manual that I could find, but it must be a different revision since not too many items in the service manual match the TV...
      02-10-2025, 04:01 PM
    • pni
      Samsun ue49ku6450 blinking red light only when press the power button
      by pni
      Hi guys I have this tv Samsung eu49ku6450 that have a problem. When I plug in the power cord the standby led starts to blink but nothing happen. Then the standby led disappear. If I push the power button I see the standby led blinking but nothing happens and if I stop to press the button I don’t have the standby led red…nothing . I don’t understand if there is a problem in the main board or in the power board or it s a firmware problem. I tried to disconnect the main board from the power board, and I know the led should turn on when the main is unplugged but nothing happen…..so could be...
      Yesterday, 02:18 PM
    • lapfix
      HP OMEN NO power no light
      by lapfix
      HP OMEN : DAG35DMBAD0
      NO power ,no short ,no corrusion
      Consumption : when charger plg in = 0.004 amp

      Only 3/5 vl are present when charger connected..when i put my red probe at the coils of 3/5volts and power on with my power suplly it try to rise than 0v.
      when try to power on using power button i note this starnge value : 3v then 0.300v then 3v !
      No light at power button led

      All coils resistances :
      Pl 2001 =3v measured with kohm.
      pl 2004 = 5v measured with kohm
      pl 6001 = 49.7ohm
      pl 4012 = vccsa = 24.4 ohm
      pl 3001 =...
      11-03-2025, 07:48 AM
    • noinimod
      Sony 55X900E no standby light, no power. Replaced mainboard already
      by noinimod
      No standby red light, nothing
      This Sony has a separate AC->DC power adapter supplying 19.5V to the TV power board (JK3)



      Disconnected JK3 power board from main board, checked voltages on all the pin outs

      At a few pins I can see the power supply providing 19.5V to the main board



      Based on the service manual triage.. it seems to be pointing towards the power board (JK3) being the most possible culprit


      LED light turns on when I disconnect LED driver board ribbon from mainboard (so i thought it is the mainboard,...
      12-22-2021, 12:58 AM
    • Akuanka
      Sony SLV-E780 Power Supply Issue – Clicking Sound, Need Help Identifying Faulty Component
      by Akuanka
      Hi everyone,

      I'm troubleshooting a power supply issue with a Sony SLV-E780 VCR. The device clicks repeatedly but doesn't power up completely. I've already replaced five capacitors, but the problem persists.

      Here's a video link https://photos.app.goo.gl/3Xki6yvCLn67gLX78​ showcasing the sound. Based on your experience, could this be due to a transformer, diode, or another component? Any guidance on what to test or replace next would be greatly appreciated.

      Thanks in advance for your help!
      11-23-2024, 01:12 PM
    • Loading...
    • No more items.
    Working...