Real wattage of LC-8500BTX

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • 999999999
    Badcaps Veteran
    • Sep 2006
    • 774
    • USA

    #21
    Re: Real wattage of LC-8500BTX

    Originally posted by Jooo
    That's what I thought.
    Well I will not fully recap it. I think that Fuhjuyy will do just fine.

    As you can see in the pictures, there are some empty holes for cables. I added a pci-e power connector salvaged from another dead psu.

    I'm probably going to use this as a psu for testing dead computers.
    Not worth a recap and I wouldn't trust it to test dead computers either because you couldn't be certain whether the computer is dead or the PSU can't handle the load if it doesn't post or run stable.

    Comment

    Related Topics

    Collapse

    • cnti
      Samsung 245B PLUS - BN44-00195A - bang and smoke - solved - tips
      by cnti
      Hi.
      BacCaps forum is awesome - thank YOU ALL for sharing knowledge!

      This is about DONG YANG PSU BN44-00195A failiure in Samsung 245BPLUS. It started with bang and smoke from the back of LCD. Downloaded diagram BM44-00192A - a bit different but I will use all parts names from this diagram [and real PSU].
      BIG CAP CP801 had 315V, on standby pin 5,2V. After shorting S_B ON (through 3,3k ohm resistor) 24V and 5,3V were missing, on CP801 was 312V.

      RM801 [real PSU: RM801 - 0,22 ohm 1W] - FAIL
      burned, measured 10M ohm.

      QM801 [real PSU:...
      10-19-2023, 05:33 PM
    • edugimeno
      Diagnose real-vintage Strong-Hammer arcade machine
      by edugimeno
      Hi there!
      My friend wants me to help him repair his old-real-vintage strong-hammer machine. Well it's only 90% real as the force applied doesn't lift the weight itself but it is measured and it moves a motor that lifts the weight

      I am attaching several pictures of the machine.
      It basically has 2 sides, left side has
      • 2 x 220->12+24v transformers
      • 2 relays (1 moves motor UP, other moves motor DOWN)
      • IGF and breakers for safety
      Right side is shown on pictures. It has 3 boards ( top-down)
      • Logic board. Receives 24AC and recitifies it into DC. Contains a uC (M80C85)
      ...
      02-29-2024, 11:05 AM
    • DynaxSC
      MSI PRO B660M-G DDR4 - real bios dump from board needed (no stock bios)
      by DynaxSC
      Hi, I have an MSI PRO B660M-G DDR4 board with damaged BIOS and i need a bios dump from a real board, along with MAC, UUID and Serial Number info (eg. a BIOS screenshot and pictures from the board stickers).

      I need to reconstruct the bios on my board, based on another bios image form a real board - meaning a bios image containing MAC address, UUID and Serial number. A stock BIOS is not suffiecient, as it is impossible to discover where the MAC, UUID and SerialNumber are stored. Tried with a similar board, but there are too much differences, and the stock BIOS is missing a lot of...
      11-17-2023, 10:56 AM
    • danny34
      Thinkpad E15 Gen2 Intel "lower wattage AC Adapter"
      by danny34
      Hello folks,

      My Thinkpad E15 Gen2 with i7 had stopped loading and wouldn't start either. I noticed the typical error with the Mosfet QB6. This has become unsoldered.

      I soldered it back on and found that the gate voltage was too low and that's why it was getting hot. Then I wanted to replace the UB7. Unfortunately the one I ordered from China didn't want to run.
      So I soldered the old one back in and it still has its 18.9V at the output of QB6.
      I stuck a thermal pad on the QB6 to cool it down a bit.

      Now the E15 is running again, but unfortunately...
      10-30-2024, 02:10 AM
    • Stefan Steff
      HP laptop smart PSU wattage
      by Stefan Steff
      Is there any software/program what recognize the PSU wattage attached to a HP laptop?... like DELL has in BIOS/Battery status...?
      Thanks!
      S.S.
      08-05-2024, 06:29 AM
    • Loading...
    • No more items.
    Working...