hp15-f233wm volts disappear

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Abdelmonzon
    New Member
    • Jun 2022
    • 1
    • Cuba
    #1

    hp15-f233wm volts disappear

    Hello friends, I am new to the Forum and new to laptops because I only repaired desktop PCs.
    I have an hp15-f233wm that gets 19.5 volts and 3.3 volts of ignition, in fact when pressing the ignition button the coils get 1.8v and 1.5 volts but they disappear immediately and come back I would like help please thanks before hand
    .
    Last edited by SMDFlea; 06-25-2022, 10:45 AM. Reason: english translation
    Tags: None
    • SMDFlea
      Super Moderator
      • Jan 2018
      • 20618
      • UK
      #2
      Re: hp15-f233wm volts disappear

      link to schematic https://www.badcaps.net/forum/showpo...01&postcount=9
      All donations to badcaps are welcome, click on this link to donate. Thanks to all supporters

        Comment

        Previous template Next

        Related Topics

        Collapse
        • Nagyesz
          Lenovo ideapad 330ICH - Dead, no volts on coils
          by Nagyesz
          Hi everyone, I replaced this motherboard because it was important to get it working, but it's been with me for a very long time. Now I finally have time to figure out what the problem is,
          I've never encountered something like this before;

          No charging light, full dead

          Lenovo Ideapad 330-17ICH
          • PL3102: 5 ohms
          • PL3001: 3.2 ohms
          • PL3101: 2 ohms
          • PL5801: 3.5 ohms
          • PL5501: 270 ohms
          • PL701: 35 ohms
          • PL501: 146 ohms
          • PL503: 390 ohms
          • PL402: OL (0.27V) +5VALW_P
          • PL301: OL
          • PL401: OL (0.03V) +3VALW_P
          + Dc-in mosfet @PQ311 pin 5 20v, pin 1-4 0V , @PQ312 no volts...
          10-11-2024, 10:12 AM
        • bembeno
          hp 8560p no display - volts on cpu coils
          by bembeno
          hp 8560p uma no volts on cpu coils
          cpu controll is max 17511
          can any one plz explain whats the requirement to this ic to startup
          05-22-2022, 03:43 PM
        • ravi_1617
          ASUS X1504 & X1404ZA no vcore power
          by ravi_1617
          Hi
          Unable to find schematic diagram .
          As i inject Adaptor power board starts its self without pressing power switch
          observed when, on 3.3 volt, 5 volt & 1.8 volts present

          No power at v-core coils (3 coils) Value Ohms reading 2 coils showing 9.4 Ohms & 9.2 Ohms ,one showing 32 Ohms
          no power at coil ,19 volt present PJP8601 entering pin 2345 (chip no BCLEXS total 20 pin

          battery is also not charging
          if i try to force power off turns OFF ,turns of after 15 seconds than on by itself

          Tried flashing few bios from this...
          Export Event
          Starts
          09-11-2024
          Ends
          09-12-2024
          09-12-2024, 10:52 AM
        • MisterAIL
          PS5 digital / No Power / No Beep / Good power supply
          by MisterAIL
          Hi everyone,

          Brought a non functionnal PS5. Apparently only a bad PSU...
          No beep, nothing.

          After some tests i found this :
          - PSU is fine (12 volts stable)
          - 12 volts line is shorted
          - DA9065 was fried, F7003 also => Replaced both of them, short is gone on 12 volts line, no dead short anywhere else.
          - By the way, nothing change. No signal, no power, no beep.

          Mesuring all rails with my workbench psu (12 volts input)
          - 0.00 amp drawing
          - 12 volts, 5 volts, 2 volts, 1,15 volts are presents (suppose new DA9065 do is...
          3.3v PMIC
          5 Photos
          03-12-2024, 03:24 PM
        • Salvador Pérez
          Help identifying the function of these two coils - MSI Delta 15 (MS-15CK1)
          by Salvador Pérez
          Hello everyone, I'm troubleshooting an MSI Delta 15 (MS-15CK1) motherboard, and I need help identifying the function of the two coils marked in the attached image. The laptop powers on and responds to the keyboard, but the screen does not turn on-neither the LCD nor the backlight. I've checked the main power rails, and all other coils seem to have the expected voltages:

          • 0.91V for the GPU
          • 1.7V for VRAM
          • 3.3V and 5V rails 1.8V for the BIOS
          • 0.9V for the CPU and iGPU 1.2V for the RAM

          However, these two coils are not showing any voltage....
          1 Photo
          03-10-2025, 11:50 AM
        • Loading...
        • No more items.
        Working...