plz i need to know this ic
Lenovo s340 15IIL FL5C5/FL535/FL435 LA-H103P REV 1.0
Collapse
X
-
-
Re: Lenovo s340 15IIL FL5C5/FL535/FL435 LA-H103P REV 1.0
The picture is too blurred,you need to read the marking code.
If the first two letters are Qq it might be a silergy SY8386BRHC
https://www.badcaps.net/forum/showpo...1&postcount=12
Qq*** SY8386BRHC - N/D (EL432 EL532 LA-H131P)Comment
-
Re: Lenovo s340 15IIL FL5C5/FL535/FL435 LA-H103P REV 1.0
Courtesy of the thread above with the SMD markings.
Qq*** SY8386BRHC - N/D (EL432 EL532 LA-H131P)Comment
-
Re: Lenovo s340 15IIL FL5C5/FL535/FL435 LA-H103P REV 1.0
See attached = UT2 helped.
This is a common USB Load Switch.
p/n G517G1TO1U
Aliexpress will have these but you should be able to replace with many others available from Mouser / Digikey / Arrow, etc.
Be sure to check the polarity of the ENABLE pin = ACTIVE HIGH to match your device.
The following will work as a drop in replacement:
https://www.arrow.com/en/products/ap...s-incorporated
* this component can support upto 3.2A peakLast edited by mon2; 07-11-2022, 10:42 AM.Comment
-
Re: Lenovo s340 15IIL FL5C5/FL535/FL435 LA-H103P REV 1.0
p/n JW7110DFNC
you can buy them from Aliexpress:
https://www.aliexpress.com/af/JW7110...psort=1&page=1
attached is an example schematic taken from another logic board that uses this IC.Comment
-
Re: Lenovo s340 15IIL FL5C5/FL535/FL435 LA-H103P REV 1.0
Hi. Package is sot23-6.
Part is from Silergy SY8032ABC
Markings of 'FK' are used to identify this part.
US $2.50 | 5pcs/lot New SY8032ABC SY8032A SY8032 FK2EA FK4SC SOT23-6 Chipset
https://a.aliexpress.com/_mt6KnEa
Do confirm your markings with any vendor before purchasing but the above device looks suitable.Comment
-
Re: Lenovo s340 15IIL FL5C5/FL535/FL435 LA-H103P REV 1.0
Hi. Package is sot23-6.
Part is from Silergy SY8032ABC
Markings of 'FK' are used to identify this part.
US $2.50 | 5pcs/lot New SY8032ABC SY8032A SY8032 FK2EA FK4SC SOT23-6 Chipset
https://a.aliexpress.com/_mt6KnEa
Do confirm your markings with any vendor before purchasing but the above device looks suitable.
Thank you..Comment
-
Comment
-
Comment
-
Re: Lenovo s340 15IIL FL5C5/FL535/FL435 LA-H103P REV 1.0
Hi. It is the correct part.
See here as well:
https://www.reddit.com/r/AskElectron...enovo_ideapad/Comment
-
Related Topics
Collapse
-
by koby058Hi
The laptop power on, fan starts and stop. Power on light remain. But the laptop does not start
Witout ram, no beep.
When off, I see 5v on one coil, but i dont see 3.3
When on, i see 5v, 3.3v, 1.2v, 1.8v
Can you help me inspect it? -
by thinkfast76Hi all , need a working Bios Dump for Lenovo s340 15IIL
Motherboard FL5C5/FL535/FL435 LA-H103P REV 1.0
Thx a lot-
Channel: BIOS Requests ONLY!
-
-
by REpairATHi,
need this Lenovo schematic please.
Customer replaced display on his own without disconnecting battery, JEDP1 burnt VCC Backlight contacts. Replaced cable and soldered pins directly to mainboard, Display (double-checked, working) now receives +12V again, still backlight stays off.
Thanks in advance!
BR, Ray-
Channel: Schematic Requests ONLY!
-
-
This specification for the Lenovo ThinkPad S145-15IIL Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the S145-15IIL boardview and S145-15IIL schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or download for...09-06-2024, 02:34 PM
-
by karloxHello! I have this card in the workshop with startup issues. The equipment arrived dead. I replaced a coil and IC RTS5448, and now the equipment is turning on with low consumption at 0.04A at 20v. I don't have the complete startup sequence; I suspect there might be a short or damaged component that I can't find. I took measurements on IC PU402, and they seem correct. The coils PL404 have 5V, PL402 has 3.3V, PZZ1, and PLZ2 have 001.0 mV, PL301 has 1.3V, and PL502 has 020.0 mV, In PLG1, I have 073.0 mV, and in PQ313, I have 5-8 19v and 1-3 1.3v. Thank you. Any ideas are appreciated. By the way,...
- Loading...
- No more items.
Comment