Re: Winbond WPC8763LDG
I have the schematic for the laptop. The Winbond chip is on page 45.
I have the schematic for the laptop. The Winbond chip is on page 45.
-
canadaboy25
-Sometimes the light at the end of a tunnel is an on-coming train -
Re: Winbond WPC8763LDG
Well I was playing around with it and ended up just soaking the chip in flux and hiting it with the heat gun. When I put it back together and powered her up, it came on! I am pleased to say I am typing this relpy from the laptop.
I want to thank everyone who took the time to reply and help me with my problem and ask for nothing in return. Thanks again to everyone on this wonderful forum!canadaboy25
-Sometimes the light at the end of a tunnel is an on-coming trainComment
-
ene kb9012 programmable
ene kb9016 programmable
ene kb9018 programmable
ene kb9022 programmable
ene kb9028qc programmable
ene kb9010 programmable
ene kb3930qf/b1 programmable
ite it8585e programmable
ite it8586e programmable
ite it8985e programmable
ite it8587e programmable
ite it8522 programmable
ite it8987e programmable
ite it8589 programmable
ite it8522 programmable
ite IT8380E programmable 192kb
ite IT8380VG programmable 192kb
ite IT8995E-128 programmable
ite it8886H... -
Hello All,
I have an issue with my Majority PETERHOUSE GRADUATE Internet Radio, it keeps rebooting at the boot logo Welcome screen. I have an another forum active in other website but due to lack of response I am posting the same here. I am positing a link below that has pictures including all the troubleshooting I have tried, appreciate if someone can take a look and give me any suggestions.
https://www.hifivision.com/threads/m...-screen.98243/
Troubleshooting Summary: Majority Internet Radio - Flash Chip... -
Hi,
I'm learning electronics(already have some basics) by fixing a FH52M LA-J891P rev1B. It come from an acer nitro 5. The charger was defaulting upon pluging. The 19V rail resistance is 0ohm (I believe that caps screw my measurement). When i inject 5A, I get a rail tension of 1.3V, and 0.8V vcccore.
Except the cpu, I cant feel anything getting warmer.
I believe that it is normal, because the cpu is "eating" half the power I'm imputing.
I dont know if the cpu is fried, because I did not remove the big capacitor on vcccore.
I believe that if the cpu was fried,... -
Hi everyone,
I hope someone can help me.
I have an Asus ROG Strix Scar 18 (G814JZ) laptop with a Winbond 25Q16JWNIG chip on the motherboard.
Unfortunately, I flashed the wrong file (BIOS/EC/other region – I'm honestly not sure anymore), and now the laptop is completely dead: no display, no fan spin, no reaction at all.
I have a CH341A programmer and I'm able to read and write to the chip. However, I'm not sure which software is best (AsProgrammer, NeoProgrammer, etc.) or if there's anything specific I should watch out for.
A valid BIOS/EC backup... -
While installing new SSD's in my new to me Dell 5520 laptop, I dropped a screw which sparked and fried a capacitor. Yes, I know I should have disconnecte the battery first Doh!😡. The laptop runs fine, but I want to replace the capacitor asap. I ordered and received the replacement (10uF, 25V 0603). Since I also managed to burn up one of the pads it was soldered to, my main question is whether it is okay to solder this capacitor on top of another capacitor (same size, same function in circuit). Specifically, PC4428 is bad and no way to easily solder to the board. I would like to solder it piggy...
Comment