Dell latitude no power on

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • quartz
    Member
    • Nov 2010
    • 14

    #1

    Dell latitude no power on

    Hi,

    forum has already identified a cap in a display power board, thanks, hoping some luck with this.

    Have a dell latitude d400 (second hand), been using ok for 12 months. a week ago, it was switched on all ok,4 hours later, came back to it and it had died. state of play is....

    as soon as i try to turn the laptop on, the LED on the power block, goes off. have to remove the ac adaptor from the mains, to get the power block LED to go on again. the moment i try to switch the laptop on, the power block led goes off again

    when attempting switching the laptop on, the laptop power button light barely flicks on, and straight off again.

    ive tried switching on with no battery and no hard disk installed, also reseated both so-dimm modules. i'm guessing either the display, or the laptop motherboard itself ?
  • LDSisHere
    Badcaps Veteran
    • May 2012
    • 727
    • U.S.A.

    #2
    Re: Dell latitude no power on

    From what you describe it sounds like you have something shorted on the motherboard or your power supply is bad. Try another known good adapter and if it has the same symptoms then you know the problem is with the laptop. If the computer works then you just have to buy an adapter.

    Comment

    Related Topics

    Collapse

    • sam_sam_sam
      Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
      by sam_sam_sam
      I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

      One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
      03-31-2024, 02:12 PM
    • sam_sam_sam
      Modification to a ZD-987 desoldering/soldering station using a external switching power supply
      by sam_sam_sam
      I have been working on this concept for quite some time now with limited success but recently I found a switching power supply that is setup for the voltage that this soldering station needs to operate at however it also needs part of the secondary circuit from the original switching power because you need several voltage rails

      I once tried to get a ZD-915 desoldering station to work on a 18 volt battery power supply but unfortunately things did not go well but I did find a work around but I might try this idea again but going at a little differently more about this another time...
      07-01-2024, 06:34 AM
    • dlonely94
      Dell Latitude 5591 not power on
      by dlonely94
      Hi everyone!
      I have a Dell Latitude 5591. It has a strange problem:

      First, when the WLAN card is plug in, it will not power on when press power button, even all voltage is up (19v, 3v, 5v, 3valw, 5valw)

      When I remove the WLAN card, it will start nomarlly. Then I power off and re-insert the WLAN card, it still work normally.

      But, if I left it for 3 or 4 days without the battery and adapter plugged in, it will not power on, and I have to repeat the above sequence.

      Sometime, when it not power on, I just unplugged the battery and adapter, wait...
      10-13-2024, 10:29 AM
    • NADJIB
      Dell Latitude 7390 _DAZ20 LA-F312P 1.0 - all power rails up except VCC_CORE and VCC_GT
      by NADJIB
      Hello,
      I need help please​

      I have Dell Latitude 7390, LA-F312P 1.0


      - power LED turns on a few one second or two withe power supply or battery
      - the power supply indicate current 0.16 A While laptop is powered
      I checked:

      While laptop is powered from battery/barrel plug AND power LED is on, all voltage rails show up, except +VCC_CORE and +VCC_GT.


      * COIL
      PL612
      - Output resistance to ground is 14.7 ohm.
      PL613 AND PL610
      - Output resistance to ground is 9.8 ohm.
      01-23-2024, 04:31 PM
    • Tynan Dill
      Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
      by Tynan Dill
      I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

      Upon bringing it home and plugging it up, it showed a standby light.

      I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

      The screen seems to blackout and stay black, but with a flashlight I can see the display.

      With my Playstation 4 connected via HDMI, and running a game I can hear sound.

      Assuming...
      11-22-2024, 01:46 PM
    • Loading...
    • No more items.
    Working...