Aoyue 738 4 in 1 solder station power board

mentholflash

Member

Join Date: Mar 2013

Posts: 36

Country: Western Australia
#41

08-07-2023, 10:20 PM

Re: Aoyue 738 4 in 1 solder station power board

I think i remembered what i did now too
I couldnt get the element out of the housing so i pulled on the wire & thermo with a pair of pliers as i was sure the heating element had died
If any of that helps
Cheers
How do i check the mcu is still alive

Last edited by mentholflash; 08-07-2023, 11:21 PM.
Comment

Previous 1 2 3 template Next

Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?

by Tynan Dill

I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

Upon bringing it home and plugging it up, it showed a standby light.

I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

The screen seems to blackout and stay black, but with a flashlight I can see the display.

With my Playstation 4 connected via HDMI, and running a game I can hear sound.

Assuming...

7 Photos
- Channel: Troubleshooting TVs and Video Sources
11-22-2024, 01:46 PM
TCL 55S425 few horizontal lines, potential failure on both side of panel/buffer board

by howardc64
All left and right refers to looking from rear of TV (or looking from front with TV upside down)
- TV came with vertical bars and no image. Found faulty TVS on left buffer board. Also replaced T-Con (may have damaged the original while hot air removing components, board has slight warp) and have full image but few horizontal lines on the screen. Some of the lines appears to be 2 pixel tall while others are 1 pixel tall.
- Disconnecting left and right buffer board potentially reveals problems on both sides with different signals (unless this T-Con require jumper like Samsung FB_TRDY1&3) Fault
...
- Channel: Troubleshooting TVs and Video Sources
07-24-2025, 05:17 PM
Solder won’t melt on MacBook 2021 logic board – need advice

by defdjamel

Hi everyone,
I’m trying to remove a component from a 2021 MacBook logic board, but I’m having trouble.
https://www.electronicsdatasheets.co...s/tlv70733pdqn
I’m using hot air at 480 °C with full airflow and good flux, but the solder paste is not melting.

I know there’s a lot of thermal dissipation from the board, and I suspect the copper planes are absorbing most of the heat.

Do you have any tips for this kind of board? Would a preheater help?

Thanks in advance!
- Channel: Troubleshooting Laptops, Tablets, and Mobile Devices
09-05-2025, 08:56 PM
A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair

by howardc64

Problem

This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
- Channel: Troubleshooting Computer Displays
08-04-2024, 10:36 PM
Guide to transplant MEC1503 EC chip and EEPROM reprogamming for T14s gen 2 and X13 gen 2

by acedogblast

This is a guide that I am writing for helping others to replace their MEC1503 EC chip if it breaks (or to get around an inconvenient prompt to the BIOS). This forum has been extremely helpful to me so I would like to contribute to help others. I will tell you right now that this task is very difficult to do. You MUST have experience and tools to do precision micro-soldering, BGA reballing, trace repair, and general laptop repair skills.

There are some specialty tools needed to do this task. The replacement MEC1503 chips can be acquired from Aliexpress. Do not buy the bare chips as...
- Channel: Troubleshooting Laptops, Tablets, and Mobile Devices
11-02-2024, 05:13 PM
Loading...
No more items.

Aoyue 738 4 in 1 solder station power board

Comment

Related Topics