imac 2017 820-00609-A mising damaged components ??

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • jimbobcress
    New Member
    • Sep 2018
    • 6
    • United Kingdom

    #1

    imac 2017 820-00609-A mising damaged components ??

    I have picked up a Imac A1419 2017 with a fault of getting stuck on the apple loading screen. Will not boot to macos, bootcamp or recovery. it will allow the drive selection option but nothing else.
    I have examined the board and noticed some damaged components next to the ethernet port. Can any one identify them and could they affect the boot issue?
    I cant find a schematic or brd for this model.

    the first picture is for reference and for the location on the board.
    the second shows the damaged component, it appears to have a cover and a copper coil underneath.
    and third shows a missing component, either a resistor or capacitor.

    Any help appreciated.
    Attached Files
    Last edited by jimbobcress; 09-18-2022, 03:54 PM.
  • smzlwan223
    Member
    • Mar 2022
    • 20
    • 中国

    #2
    Re: imac 2017 820-00609-A mising damaged components ??

    The network card end dropped, which should have been accidentally knocked off when removing the motherboard. This will not cause this situation. In my past personal maintenance experience, I have encountered: 1. The hard disk is partially damaged, 2. The WIFI module, 3. The memory is not lit or damaged, 4. The video card is partially faulty. You can first remove and disconnect the hard disk cable, and then insert and install the Apple system USB flash disk, Check whether you can successfully access the USB disk installation interface. If you can, then you can replace a hard disk to install the system. If you can't,

    Comment

    • jimbobcress
      New Member
      • Sep 2018
      • 6
      • United Kingdom

      #3
      Re: imac 2017 820-00609-A mising damaged components ??

      Originally posted by smzlwan223
      The network card end dropped, which should have been accidentally knocked off when removing the motherboard. This will not cause this situation. In my past personal maintenance experience, I have encountered: 1. The hard disk is partially damaged, 2. The WIFI module, 3. The memory is not lit or damaged, 4. The video card is partially faulty. You can first remove and disconnect the hard disk cable, and then insert and install the Apple system USB flash disk, Check whether you can successfully access the USB disk installation interface. If you can, then you can replace a hard disk to install the system. If you can't,
      Sorry I don't understand your reply?? Have you missed something?

      Comment

      • jojo1228
        New Member
        • Oct 2023
        • 1
        • India

        #4
        Re: imac 2017 820-00609-A mising damaged components ??

        Originally posted by jimbobcress
        Sorry I don't understand your reply?? Have you missed something?
        did you find the solution?? I also have the same issue on me board..

        Comment

        • Marhell
          New Member
          • Oct 2023
          • 1
          • Germany

          #5
          Re: imac 2017 820-00609-A mising damaged components ??

          Get schematic and identify the missing components. The 3rd one is a capacitor. But you also need the value.

          Comment

          Related Topics

          Collapse

          • tommy97
            iMac Pro 2017 A1862 SSD Upgrade & Recovery mode
            by tommy97
            Hi,

            we've got iMac Pro 2017 which having a problem with SSD, iMac come with 2 SSD's 1TB, it was having a problem with the SSD so we get the replacement, installed in and iMac is stuck in recovery mode, tried to restore it & revive, nothing worked - error 4010. After installing old drives now we're having the same problem that the device is in recovery mode. Previously after swap of the SSD iMac worked on the old SSD however after attempt of revive on the new SSD machine stuck in recovery mode, I can go to DFU but the same result with error 4010.

            Any ideas what might've...
            04-20-2024, 04:48 AM
          • 944longdrift
            Help Identifying board components - iMac 2017 21.5
            by 944longdrift
            2017 iMac (Mid 2017) A1418

            I'm not quite sure how this happened but a couple of components got ripped off the board when removing from the Logic Board from the iMac.

            Can anyone help identify them?

            I'll have to do the trace repair on the board before soldering on replacements but would prefer to order the components rather than get a whole scrap logic board off eBay.
            Thank u


            ...
            03-14-2024, 11:53 AM
          • iZakre
            HP Pavilion 15 bc400ns - Complete Black Screen - Only video on live usb
            by iZakre
            Hello everybody!

            To put you in context I recently replaced the battery from my HP Pavilion 15 bc400ns with a used one, everything was going good. The same day, I decided to update the BIOS, everything went good. The thing occurred after I let the battery drain iddling on Windows 11 for the second time to calibrate it that the screen did not turn on again, the computer was on but the screen did not turn, like it would not wake from hibernation. I decided to restart the computer but got no video.

            The thing is that I had installed TeamViewer and could log into the computer...
            02-19-2023, 02:27 PM
          • mat2k
            iMac 2017 PSU - shorted PFC mosfet
            by mat2k
            I am trying to fix an iMac 2017 PSU, initially came with a blown fuse and shorted PFC MOSFET (6R199P). After visual inspection and some measurements I replaced the FET with a P20NM60 and tested with 100w series lamp, and it lasted 1 second before going into dead short. The PFC controller chip (NCP1605BG) and its passives appear fine (passives measure OK), but I do not know if there is a simple way of testing the NCP1605 as I wouldn't like to blind-replace it.
            There was some slight blackening of the solder on the PFC controller passives so I reflowed them all with some flux. I am waiting...
            03-13-2025, 11:31 AM
          • mon2
            In search of T2 rom dump for iMAC 2017 A1862
            by mon2
            Hello all. Have an imac that is not able to create PP1v8_S5 and there are no shorts on the rail. Unable to DFU due to USB not working. Suspecting corruption of the T2 firmware.

            Welcome all suggestions. Thanks.
            08-13-2024, 08:13 PM
          • Loading...
          • No more items.
          Working...