hp w2207h - died

Collapse
X
Collapse
 
  • Page of 3
  • Time
  • Show
Clear All
new posts
Previous 1 2 3 template Next
  • slayer200230
    New Member
    • Jul 2015
    • 5
    • usa
    #41
    Re: hp w2207h - died

    also if these 2 caps are in parallel does it matter the order? looking at the bottom circuit it looks like these 2 are both tied between ground and positive, from the rectifier, ofc i could be wrong and would rather get it correct, also this board can be found all over the internet, just cant read the values of the caps
    http://lcdalternatives.com/HP-W2207-...-P2378564.aspx

    if anyone is interested maybe they can find the one picture that shows one of the 2 values

      Comment

      • slayer200230
        New Member
        • Jul 2015
        • 5
        • usa
        #42
        Re: hp w2207h - died

        ok just got back to work where the resistors were, they are slightly diffrent sizes so i was able to match them up c819 is the 1000uf cap at 10v, whats great is i ordered 1200uf 16v caps and got 2200uf 10v caps instead. so my bad. c818 is the 1200uf 16v cap

          Comment

          • nasnus123
            Member
            • Jan 2016
            • 28
            • india
            #43
            Re: hp w2207h - died

            HI
            I have HP w2207h 22 inch LCD Monitor , power on but led blnking blue and orange ,I test power supply outputs they are 5v and 15V , there is no number on inverter chip Inverter Controller pin4 2.2v and 0v follow by led blinking , what could be the problem please replay me .

              Comment

              • nasnus123
                Member
                • Jan 2016
                • 28
                • india
                #44
                Re: hp w2207h - died

                on pin 4 signal coming from logic board

                  Comment

                  • chumy
                    Member
                    • Mar 2012
                    • 23
                    • indonesia
                    #45
                    Re: hp w2207h - died

                    Need EEprom HP W2207H

                      Comment

                      Previous 1 2 3 template Next

                      Related Topics

                      Collapse
                      • hs5424
                        Dynacord powermate 1600 block diagram.
                        by hs5424
                        Hi All,
                        I obtained a schematic diagram for the above mixer but I am wondering if a block diagram exists as I am trying to fix a problem in the protection circuit which I find a little confusing using a circuit diagram only. In the good old days the workshop manuals always had a block diagram with a circuit discription. Very useful for fault finding.
                        The protection light is perminently on. The right sode has a -80DC on the feed to the speaker, hence the protection led on. I have removed all the O/P transistors which checked out OK. I tested all other transistors in circuit which seem...
                        07-31-2025, 01:35 PM
                      • gabri2211
                        I'm looking for the wiring diagram for led monitor model DHI-LM19-L200
                        by gabri2211
                        hello everyone, I'm looking for the wiring diagram of this led monitor.
                        the model is DHI-LM19-L200, but I think that any other diagram of a DAHUA monitor could be equivalent.
                        I really hope that among you someone can help me to repair this monitor, the screen is black, it doesn't seem like a backlight problem.
                        I see the presence of 12 volts, 5 volts, but without a diagram the repair is very difficult.
                        thanks to those who will answer
                        1 Photo
                        12-10-2024, 04:37 PM
                      • bohaboha
                        Samsung UE70TU6905 BACKLIGHTS AND SOUND ON NO PICTURES BUT SCREEN NOT DARK
                        by bohaboha
                        Hi it looks like everything works don't know where to test except the 390v in the 2 capacitor in the hot side of the power supply and the weird 180v in the diodes in the cold side that should be discharged it is writin on the circuit no more you can read what is written on the circuit quite srrange color mixiing yellow and white
                        anyhow i couldn't t read anything else
                        the backlight is on strong and the screen does not get dark or very dark but no pictures
                        the mainborad feels a bit hott on the black part i test it to 52 degree's against 34 to 40 on the rest of it
                        ...
                        01-02-2025, 08:04 PM
                      • valvashon
                        LG 55UH6150- trouble powering up, then half lit screen (pictures!)
                        by valvashon
                        The 55" LG has been in the basement for a few months without being used. Turned it on yesterday, set came on as it should and showed a complete screen for about 5 seconds (was on a broadcast channel but no antenna was connected), then the screen went mostly dark with about 1/3 of the screen on the right lighting up with brighter lines in that lit part (sorry, no pictures of that). Power LED was cycling too, preventing the TV from fully powering up.
                        Pulled the back off, all boards looked OK. Pulled the LED connector, turned the set on to see if it would power up but I don't belive it...
                        11-24-2024, 12:08 PM
                      • TinkerTron
                        Schematic vs. Reality: Where Are the Resistors on My Sharp Clock Radio? Model FY-70CH
                        by TinkerTron
                        Hey everyone,

                        I'm currently working on a mid-70s Sharp Electronic Digital Clock Radio, Model FY-70CH. I found the service manual online, printed it out, and have been studying it for a while. My main reasons for tackling this are: (1) I want to learn electronics and figured I'd start with something I had on hand, and (2) I want to fix its issues. Right now, the radio sounds awful, has about 5V DC at the speaker terminals, and the alarm time setting doesn't work. But I'm not asking how to fix these problems.

                        Instead, here's what's been bugging me so far:
                        The schematic...
                        3 Photos
                        03-06-2025, 02:03 PM
                      • Loading...
                      • No more items.
                      Working...