Hanns-g hz281

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • prpockets
    New Member
    • Jul 2017
    • 6
    • usa

    #1

    Hanns-g hz281

    I have Hanns-g, HZ281 monitor that starts out just fine but goes to black intermittently while the light stays blue and I cannot see any image on the screen. As the monitor warms up the frequency going to black increases. For several years I have had a fan blowing on the back of the monitor and that has helped but now the frequency of going to black has increase to the degree that it is no longer tolerable. I have 3 of these monitors so it is certainly worthwhile that I learn how to repair this one. There are no capacitors that are bulging or show any sign of heat damage they all look good to me.
    I have read HG 281 thread along with its over 700 posts, so that is the sum of my experience on this matter.
    So given the symptoms and the HG 281 posts I am going after the capacitors on the logic board.
    I have learned that the best cap manufacturers and the correct series to replace the capacitors are:
    Panansonic-fm, fc, fr
    United Chemicon- ky lxz, kze
    Rubycon- yxg, yxh, tzl, zlh, zlg, mbz
    Nichicon-pm, pw, he, hd hv, hm, hz
    And the capacitor(s) on the board are: and from Digi-Key are to be replaced with:
    (11) 100uF 16v and replace with Panasonic p14391-nd, fr series
    (5) 10uF 50v and replace with Chem con 565-1702-nd, kze series
    (3) 220uF 16v and replace with Panasonic p19484-nd,fc series
    (1) 47uF 16v and this is the one I am have trouble with so I increased the volts to 25 and found
    Panasonic p12923-nd, fm series or chem con 565-1672-nd but here is where I get confused both caps are listed as bulk but at the end of the listing is says packaging is radial can, I only need one but thinking ahead I may order enough to fix all three monitors which means a total of three.
    Could someone please take a look at my replacement capacitors and verify that I am ordering the correct capacitors.
    While I am at it I might as well order solder I believe the 60/40 with rosen core is the correct one?
    Any assistance with this monitor be it diagnosis, repair or cap replacement will be very much appreciated.
    Attached Files

Related Topics

Collapse

  • momaka
    HannStar Hanns-G HC194d LCD monitor repair
    by momaka
    Normally, I never post repairs this quick after I do them, because… I am usually very slow. But today, I’m making an exception here. Why? No idea. Perhaps only because the repair details are still “fresh” in my head… which is ironic, given this is a 16 year old monitor that hardly anyone will care about today. It is new to me, though. I picked it up last November from someone on my local Craigslist. It wasn’t very close to where I live, but was close to a family friend that I had to go visit anyways. So after watching the posting on Craigslist for a few weeks and seeing it getting...
    03-15-2023, 10:17 PM
  • psyduck
    Conformal coating on Samsung U32D970 monitor PSU, do I need to replace after repair?
    by psyduck
    I have a Samsung U32D970 monitor from 2015 I pulled out of the bad hardware pile that turned on and then turned itself back off after a few minutes of use and refused to turn back on. The PSU has part number BN44-00786A, and I found a couple posts about one that had blown with damage to the MOSFETs and PWM controller - but nothing about intermittent failures. I started a new thread and said that I would refresh the solder joints on the board to see if it was just a bad connection and possibly replace the PWM and PFC ICs. I then asked what my next course of action would be after those steps. I...
    11-27-2023, 06:56 PM
  • ant3202
    HP 27es - LED monitor - Monitor Flashing On - Off
    by ant3202
    Hi Everyone

    Lately I am experiencing the deja-vu incident on one of the led monitor like this.
    https://www.badcaps.net/forum/troubl...lashing-on-off

    The monitor is HP 27es LED Monitor
    https://h30434.www3.hp.com/t5/Deskto...e/td-p/6804692

    The monitor will randomly blackout and display no signal and will recover again.
    Sometimes need to power and off again to restore the display but...
    03-20-2025, 07:30 PM
  • Rick_1234
    LG 23MP55HQ LED Monitor turns off after a few seconds or flickers.
    by Rick_1234
    Good evening, gentlemen.

    I have a problem with my monitor. It turns off after a few seconds or flickers. Shining a flashlight on the screen doesn't show any image, so I guess it's not the "2 seconds to dark" I read in the forum.

    To turn it back on, I have to press the power button twice. Then after a few seconds it turns off again or flickers. See video.
    https://drive.google.com/file/d/1L6S...ew?usp=sharing


    Things I tried

    - Bought a new AC adapter thinking that was the problem but the problem...
    06-22-2024, 04:44 PM
  • momaka
    Wise Wing F199 19'' LCD monitor - recapped
    by momaka
    Looking through my repair pictures and notes, it's been a long time since I posted anything in the LCD monitors section. So here goes that.

    I'm dedicating this thread to one of the very first LCD monitors I repaired (if not the first one), which was more than 10 years ago now. The monitor is a Wise Wing, model F199. It's a 19” CFL-backlit LCD. I got it for free off of Craigslist in 2009 from a guy, who said he bought it for cheap from Wallmart and the monitor worked only for a little less than 2 years before quitting.

    When I saw the Craigslist post, I wasn't...
    08-24-2020, 10:58 AM
  • Loading...
  • No more items.
Working...