Gateway LP2407 / FPD2485WA - Anyone have assembly photos, steps or hints?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • emericono
    New Member
    • Jan 2014
    • 8
    • USA
    #1

    Gateway LP2407 / FPD2485WA - Anyone have assembly photos, steps or hints?

    Does anyone know where I can find close up and/or high-resolution pictures of the insides of the Gateway 24" model: LP2407 / producet no.: FPD2485WA (partially assembled)? I'm trying to assemble one someone previously disassembled, not sure which screws go where, unfortunately. I believe I have all the screws and parts.

    Any help is greatly appreciated. The relevant posts I came across on here didn't have adequately clear pictures to help identify which screws go where.
    Last edited by emericono; 11-03-2014, 03:12 PM.
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • howardc64
      A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
      by howardc64
      Problem

      This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
      08-04-2024, 10:36 PM
    • ElectricDoodler
      Lenovo Thinkpad X230T Convertible - display assembly and touch digitizer
      by ElectricDoodler
      I need the schematics and boardview for the display assembly and touch digitizer for an X230T convertible tablet from Lenovo. Would anyone happen to have them?

      I have one in perfectly working condition, and I've been primarily using it as a drawing tablet for a while. But the CPU is showing its age with it not being able to handle larger canvases, so I would like to remove the display assembly and use it as a USB drawing tablet, and I need to verify the pin-layouts of the touch digitizer to do so.

      Model: X230T (type 3437-23G)
      Display FRU 04W3919
      Display P/N...
      01-19-2025, 12:57 AM
    • bjhnsonjr2734
      Gateway laptop model GWTN-156-7BL Needing Schematics
      by bjhnsonjr2734
      I am really needing Schematics for the motherboard on my Gateway laptop model GWTN-156-7BL

      I attached a pic of motherboard info



      ...
      04-25-2025, 07:01 AM
    • Dan John
      Gateway P5WS0/NV57H58u laptop (P5WEO LA-6901P REV:2.0) - (Possible) Multiple Issues
      by Dan John
      Greetings everyone,

      I have a Gateway P5WS0/NV57H58u laptop (P5WEO LA-6901P REV:2.0). The client said the battery was not charging. Upon checking the laptop,

      1) On pressing the power button, the (power button) light turns on and stays on.
      2) There is no boot, or anything on the screen.
      3) The fan starts and stops a few times, then it stops completely.
      4) The light on the power button remains on.
      5) Battery not charging (original issue).

      The original problem was that the battery was not charging, but the laptop still worked. My belief      ...
      Voltage Tracking Steps
      5 Photos
      04-23-2025, 08:12 AM
    • abajor
      A3401 Gatorade Spill Best next steps
      by abajor
      I had a customer call me with an M4 A3401 her daughter spilled a gatorade into, and didn't tell her mom for about 2 hours.
      I had her bring it in immediately so we could disconnect the battery and I could dismantle it so I could swab the board with Isopropyl an dry with a heat gun.
      There was already some green copper corrosion when I opened it.

      I did a good first pass and dried off the board, now I'm going over it with my scope swabbing and poking at any oxides with my exacto tip.
      I brought out my hot air tool to evaporate the iso and caramelized sugars started bubbling...
      02-16-2025, 08:01 PM
    • Loading...
    • No more items.
    Working...