interm m1000 clip lights

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • andy smith
    New Member
    • Jan 2021
    • 6
    • uk
    #1

    interm m1000 clip lights

    Hi all my name is andy
    I have a interm m1000 amp that has both clip lights on. I have checked DC on speaker outputs and is 0 volts , can anyone offer any advice

    thanks andy
    Tags: None
    • lotas
      Badcaps Legend
      • Jan 2016
      • 4564
      • Russia
      #2
      Originally posted by andy smith
      I have checked DC on speaker outputs and is 0 volts , can anyone offer any advice
      You see 0v at the output because the relay did not work due to protection.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • Delicieuxz
          I replaced all electrolytics in subwoofer, still get a hum in speakers - audio clip
          by Delicieuxz
          I get a faint, low hum through my PC speakers, which connect to the subwoofer in a 2.1 speaker system. The hum drives me crazy and makes me stressed. When I turn off the subwoofer, everything is quiet and I start to relax, lol.

          Here's an audio clip of the sound coming from my speakers:

          https://vocaroo.com/16HaryHwTx78

          I recorded with my phone's mic right next to the speaker, and the mic picked up a lot of speaker noise over top of the hum. But I don't hear that noise in the room, I just hear the lower-pitched hum that's buried beneath all the other...
          11-15-2023, 09:50 PM
        • Francesc V.
          Christmas lights - Something I am doing wrong
          by Francesc V.
          Hi:

          i am trying to repair this Christmas lights from my parents. They are incandescent lights, no led lights.

          I have tried with 12V a 24V small lights that I found in Aliexpress but is obvious that are not the right ones. They last microseconds connected. Do they blow because of Amps or Volts?

          If I measure the Amps in the string........it's only 90mA. If I measure the Volts in the "green box"......it's between 0 and 190V, but doing a little bit of maths from the number of bulbs in series.......it's only about 6V per lamp.

          Could...
          03-11-2023, 07:38 AM
        • ChaosLegionnaire
          correct way to connect bare speaker wires into spring clip terminals?
          by ChaosLegionnaire
          i recently bought a logitech z607 surround system. however, its giving me grief. when i first connected it, it only had sound coming from the front right speaker. after a great deal of fiddling and reseating the speaker wires into the spring clip terminals, i finally had sound coming from all 5 satellite speakers.

          however, the sound still gets cut off intermittently if i move the speakers, subwoofer or move/touch the speaker wires on the back of the subwoofer. so i wanna ask what is the right way to connect bare speaker wires into spring clip terminals?

          i googled...
          10-27-2022, 06:19 AM
        • bialag
          Lenovo ThinkPad E14 Gen 5 - Not Powering On - 3 Blinking Lights - 20 volts 0.224 amps
          by bialag
          Hello,

          I have a Lenovo here that does not want to power on. The motherboard appears to be clean, no sign of corrosion or obvious fried components. When plugged in, I see 3 blinking lights and then off. It would cycle the 3 blinking lights every 10 seconds or so as long as I have the adapter plugged in. Amp meter shows 20 volts, 0.224 amps, no fan spin, red light indicator near the charge port.

          Thermal camera shows a section of the motherboard that is warmer than the rest. It is near the connector labels JRTC1 (CMOS battery). Diode measurement to ground for pin 1 = OL,...
          03-25-2025, 05:56 PM
        • gabrielA7
          IMAC A1418 / MB: 820-00430-a / does not turn on, Lights 3 of the 4 LEDs and turns off.
          by gabrielA7
          Does not turn on, lights 3 of the 4 LEDs and turns off and stays like this, presses the power and repeats.
          I saw that the room LED lights up only when the screen is connected, so quiet.

          We have all the power supplies, even processor, 1.8V
          One thing I found strange, it has a very low resistance in the Vcore is giving 1 Ohm , work with notes and such, I know that this is normal in some processors but with this resistance only take video card so found it strange.

          I suspect that there may be some leak in the processor.
          Anyway, when I press the power, it...
          10-29-2024, 06:48 AM
        • Loading...
        • No more items.
        Working...