bad relay - looking for a replacement

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • vball
    New Member
    • May 2021
    • 2
    • USA
    #1

    bad relay - looking for a replacement

    Mouser #:653-G4B112T1FD130A24
    Mfr. #: G4B-112T1-FD-US-RP-T130 AC24

    I had a relay go bad in my Kenmore vacuum and it is no longer in stock from any appliance parts sites. I found the relay on www.mouser.com with numbers above.. but it is also not available from mouser. Can someone knowledgeable suggest an equivalent substitution from the mouser site?

    Thanks,
    Joe
    Tags: None
    • R_J
      Badcaps Legend
      • Jun 2012
      • 9579
      • Canada
      #2
      Re: bad relay - looking for a replacement

      This might work
      T9CP1A54-24 Mouser # 655-T9CP1A54-24 SPST, N.O.
      1-1649341-7 Mouser # 655-1-1649341-7 SPDT, N.O.

      Mouser site https://www.mouser.com/Electromechan...z0x3baZ1z0x3ca
      Last edited by R_J; 08-21-2021, 01:22 PM.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • CoinCoin88
          Garage door RX unit (Cardin S38C) does not short relay to send opening signal
          by CoinCoin88
          Hello everyone,

          I'm turning to the Badcaps community to help me troubleshoot the radio Rx card from my (old) garage door opener. While I could just ditch that card and replace the whole system, I first would like to understand "why" it suddenly stopped working, because that's just how I am wired...!

          Some basics: the receiver works on a 30.875 Mhz frequency. Yes, I'm aware this is not in use anymore in a looot of places. It does not use any rolling code, it's just a regular dip-switch code that you have to set up on both the receiver and transmitter. The receiver...
          09-15-2025, 03:36 AM
        • CapLeaker
          Kenmore electric range replacement infinity switch?
          by CapLeaker
          Actually this range had multiple problems but I fixed all the others already.

          I am stuck finding a replacement infinity dual burner switch for a Kenmore C970-605121. The dual burner is stuck full on as soon as you turn the knob either side, either the difference of either only one or both burners running full tilt.
          I tried cleaning it inside contacts, but that didn’t do anything.

          I believe the dual burner switch reads a part number of: 318191021 which is hard to find. I came across a 318191026 part number but it has 2 pins on the row missing. Is there anything...
          05-14-2023, 12:03 PM
        • steves7839
          Blomberg electric dryer - Need a replacement relay
          by steves7839
          A neighbors Blomberg electric dryer has been tumbling OK but refused to heat. The heater coil and sensors test OK.
          The control board relays are pictured. Only one of the four cannot be activated with current to the relay coil terminals from a 9V battery.

          What brand/manufacturer is this relay? I've tried searching the numbers on the Digikey website to no avail....
          08-26-2022, 09:25 PM
        • Benass
          Looking for Suitable Relay Replacement.
          by Benass
          Hello. I have Industrial Washing Machine PCB.

          Customer Requested Relays Replacement.

          I can't find WJ115F1 relays to buy. Looking for some help to identify possible alternative solutions.

          Or any tips, on how to approach this situation....
          04-21-2023, 01:51 PM
        • jm1234
          9V relay temperature 40C
          by jm1234
          Hi, I'm seeing one 9V relay having temperature 40C on its 9V (primary) side. Does that seem right? I switched 2 relays on that board and the temperature was the same (on the same position), so I'm sure it's not a faulty relay. I measured voltage on that relay and it was 9.5V DC, so that looks good. I don't see any other relay on that board having that kind of temperature and they have 9V on them too.
          I thought maybe the transistor that is switching this relay keeps switching on/off, so I also checked for AC and there was almost none: 0.3V using mV range. No steady frequency was shown, but...
          05-09-2024, 03:03 AM
        • Loading...
        • No more items.
        Working...