hair straightener Soldering hotplate

[diif]

Re: hair straightener Soldering hotplate

I got mine from Aliexpress for £2.50/$3 delivered.
It's 200V AC, I just need to wire it up with a switch and fuse.

[sam_sam_sam]

Re: hair straightener Soldering hotplate

Those PTC elements come in all different temperatures. I'm pretty sure there is a reason the one ShopJimmy uses in its LED hotplate is 480F/250C.

You can get them felbay and price is reasonable

[diif]

Re: hair straightener Soldering hotplate

Those PTC elements come in all different temperatures. I'm pretty sure there is a reason the one ShopJimmy uses in its LED hotplate is 480F/250C.

[capwizard]

Re: hair straightener Soldering hotplate

Samuel, believer or not it is 110v.

Forget about changing resistor, it will not works because I connect it to 110v ac outlet, it still not working, the PTC heating element when it reaches a certain temperature it just dropped the current it will never reach too high temperature even I put it on variac, but it will make a solder ball which I used it to test temperature (picture 3), so, I think I will use DC to drive it. look at the pictures.

[sam_sam_sam]

Re: hair straightener Soldering hotplate

What voltage do these heating elements work on

[capwizard]

Re: hair straightener Soldering hotplate

my friend, This is exactly what I want to do.

The goal I want to achieve is to change a SMD resistor then I can turn this hair straightener into Edge LED Strip Desoldering Mini Hotplate with PTC Heating Element. (The other side of PTC heater can be use as a spare part)

--------------------------------------------------------
PTC Heating Technology Benefits. ... PTC (Positive Temperature Coefficient) is a unique technology that eschews traditional resistance wire and replaces it with ceramic stones or chips. This simple switch in materials is what makes PTC electric heaters superior to traditional coil electric heaters.

PTC ceramic elements: PTC ceramic material is named for its positive thermal coefficient of resistance (i.e., resistance increases upon heating). While most ceramics have a negative coefficient, these materials (often barium titanate and lead titanate composites) have a highly nonlinear thermal response, so that above a composition-dependent threshold temperature their resistance increases rapidly. This behaviour causes the material to act as its own thermostat, since current passes when it is cool, and does not when it is hot. Thin films of this material are used in automotive rear-window defrost heaters, and honeycomb-shaped elements are used in more expensive hair dryers and space heaters.

[sam_sam_sam]

Re: hair straightener Soldering hotplate

You might be able to play with U1 PIN number 2 with VR 1 and the resistance of the resistance divider but you will have find which the VR 1 side it is close to 0 ohms at full temperature setting

[capwizard]

Re: hair straightener Soldering hotplate

brand is SUTRA, I bought it for $3 over Goodwill.

[sam_sam_sam]

Re: hair straightener Soldering hotplate

Adjustable temperature, 140F-450F, hair straightener can it be a LED desoldering hotplate?

I found this hair straightener can turn up to 450F, can it be use for LED strips desoldering hotplate? more Green than clothes iron, smaller and more convenient and looks better.

I tried it and it could melt down the solder (picture 5), but it couldn't thermal separated the LED on the strip.

Does anyone know how can I increase the hair straightener temperature?

By the way what brand name is unit I might have a use for something like this

[capwizard]

Re: hair straightener Soldering hotplate

What is on the other side of this board
Please post pictures

Also is there a part number on the heater elements

Over here: LM358 and a TRIAC, two black wires is thermistor, two red wires is PTC heating element.


hair straightener control circuit principle is as same as this (picture 2).

[sam_sam_sam]

Re: hair straightener Soldering hotplate

What is on the other side of this board
Please post pictures

Also is there a part number on the heater elements
But from the looks of the photo it has heater element
some type of temperature sensor to some type of temperature controller ( you might be able to play around with the resistance that controls the temperature but you would need to how this device works and how it is used to know what to do with it )

Depending on what type of temperature sensor it has would determines what type of temperature sensor you can use and use a better temperature controller

[budm]

Re: hair straightener Soldering hotplate

As you know about the LED strip construction, most of them just use double-side PCB (Copper on top and copper on the bottom with fiberglass sandwiched between), to heat transfer between to the top and bottom is very poor since they cannot use Thermal Vias, that is why I have been saying for a long time about thermal management for these TV with LED backlights, The heat transfer from the top layer to the bottom layer is very bad.
So if you check the temperature of the bottom and the top side you will see what the actual temperature of the top side of the board is compared to the bottom.
https://micro.rohm.com/en/techweb/kn...cdc_pwm03/3256

[capwizard]

Adjustable temperature, 140F-450F, hair straightener can it be a LED desoldering hotplate?

I found this hair straightener can turn up to 450F, can it be use for LED strips desoldering hotplate? more Green than clothes iron, smaller and more convenient and looks better.

I tried it and it could melt down the solder (picture 5), but it couldn't thermal separated the LED on the strip.

Does anyone know how can I increase the hair straightener temperature?