Do I need to remove diode from board to test it?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Nolina1234
    New Member
    • May 2013
    • 1
    • USA

    #1

    Do I need to remove diode from board to test it?

    Can I get accurate tests while leaving the diode connected to the board or do I need to remove at least one leg? Thanks!
  • mariushm
    Badcaps Legend
    • May 2011
    • 3799

    #2
    Re: Do I need to remove diode from board to test it?

    You need to remove at least one leg.

    Comment

    • Mad_Professor
      A Mech Warrior
      • Feb 2011
      • 1587

      #3
      Re: Do I need to remove diode from board to test it?

      You can remove it or remove one leg for an accurate read.

      Comment

      Related Topics

      Collapse

      • howardc64
        A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
        by howardc64
        Problem

        This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
        08-04-2024, 10:36 PM
      • Tynan Dill
        Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
        by Tynan Dill
        I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

        Upon bringing it home and plugging it up, it showed a standby light.

        I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

        The screen seems to blackout and stay black, but with a flashlight I can see the display.

        With my Playstation 4 connected via HDMI, and running a game I can hear sound.

        Assuming...
        11-22-2024, 01:46 PM
      • tvguy12012012120
        Zombie Samsung UN55NU6900F dead / no standby voltage - randomly came to life after hours of troubleshooting then died
        by tvguy12012012120
        This is my first attempt at troubleshooting a board like this, I know I could just buy a new board but I'm curious to figure out how this works. I've been testing different components in the evenings this week and I think the problem is with the IC failing to start up for some reason. When the board is plugged in there is no standby voltage.

        Then today it randomly sprung to life like a zombie but shortly died thereafter. I have no idea why it would have done that and its the first time I've seen it running. I discharged capacitors on the board last night, then it was sitting today....
        02-07-2025, 05:13 PM
      • howardc64
        TCL 55S425 few horizontal lines, potential failure on both side of panel/buffer board
        by howardc64
        All left and right refers to looking from rear of TV (or looking from front with TV upside down)
        • TV came with vertical bars and no image. Found faulty TVS on left buffer board. Also replaced T-Con (may have damaged the original while hot air removing components, board has slight warp) and have full image but few horizontal lines on the screen. Some of the lines appears to be 2 pixel tall while others are 1 pixel tall.
        • Disconnecting left and right buffer board potentially reveals problems on both sides with different signals (unless this T-Con require jumper like Samsung FB_TRDY1&3) Fault
        ...
        Yesterday, 05:17 PM
      • gusto
        How do I remove the chip from the board
        by gusto
        I am new to hot air soldering. I need to remove one chip from the board. I have a hot air solder and I set the temperature to 350°C. I slowly started heating the chip, but the solder didn't melt. I heated it for about 5 minutes, but the solder still wouldn't melt. I increased the temperature to 450˚C and still nothing. After a while, the board started to change color, but the solder still didn't melt.
        Fortunately, I'm testing it on old network switches to see how it works.
        What am I doing wrong?
        I've seen a lot of videos on youtube and everyone got the solder melted and the...
        10-08-2024, 10:55 AM
      • Loading...
      • No more items.
      Working...