Capacitor substitution

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • mariushm
    Badcaps Legend
    • May 2011
    • 3799
    #21
    Re: Capacitor substitution

    Good job. But I have to point out that capacitor AFTER the regulator is important, otherwise the 12v output will be unstable.

      Comment

      • flinx
        Senior Member
        • Aug 2010
        • 132
        • USA
        #22
        Re: Capacitor substitution

        Originally posted by mariushm
        Good job. But I have to point out that capacitor AFTER the regulator is important, otherwise the 12v output will be unstable.
        That will have to wait till I have something to mount it on.
        "...off the record, unnamed government sources
        alluded to unsubstantiated innuendos about
        alleged indiscretions and insinuated that they
        are rumored not to be without basis for further
        speculation..."

          Comment

          Previous 1 2 template Next

          Related Topics

          Collapse
          • chth96
            Is it no harm to replace with capacitor without ripple current rating?
            by chth96
            When I tried to repair LG 29 inch CRT TV, I found that the ESR value of samyoung SMS capacitor(160v 2.2uf), which is very close to D1879 transistor, is 6 ohm.


            Judging from above ESR Meter Table,I think It is necessary to replace this sms capacitor.So I visited local electronics shop,and I purchased 160v 2.2uf rubycon YK capacitor.
            But when I browse through rubycon YK datasheet,I found that there is no ripple current rating for 160v 2.2uf specification. But On the contrary, I found 39 mA ripple current rating for 160v 2.2uf SMS capacitor.
            Rubycon YK DataSheet (b...
            04-19-2024, 05:19 AM
          • Prolog
            RTX 3080 FE Identifying capacitor
            by Prolog
            Hi people, I hope this is the correct spot to post this, I'm new to the forum.

            I have an RTX 3080 Founders Edition which has a burnt up capacitor (it was in parallel with another capacitor which appears damaged too), so I am hoping to be able to identify the capacitor values and order replacements.

            I hope these photos make it clear which component I am referring to:
            (yes, the soldering is a bit botched from removing the blown one, I know)

            I have found the board schematic (attached), but there does not seem to be a boardview available. I have never...
            12-01-2024, 08:27 PM
          • Ady2017
            Is it ok to use a capacitor with a much higher ripple?
            by Ady2017
            Hi all

            I am trying to source some new caps for the power board on my LG TV. The one I am currently struggling to find a replacement for has the specs:
            Sam Young KMG 680uf 50V with a rated ripple current of 973. According to the catalogue these seem to be a general purpose capacitor and it is not clear why LG have used them on the power board.

            I like to use Panasonic capacitors but most of these have got a ripple voltage of 2-3 times the figure of the original capacitor. My preferred FR capacitors are 3160 while the FC ones are 2215. Would going from 973 to...
            10-30-2021, 10:46 AM
          • chth96
            How can I test non-polarized capacitor?
            by chth96
            I desoldered samwha NF capacitor(50v 5.6uf) from PCB circuit of 29inch CRT TV which have symptoms of no display after I heard sound of inrush of current to TV whenever I switch on this television.
            I measured ESR value of this non-polarized capacitor(samwha NF capacitor 50v 5.6uf) by means of MESR-100 ESR meter and It displayed 0.3 ohm

            And When I measured its capacitance with digital multimeter and LCR-T4 Mega328 meter, It displayed 10uf from DMM and 8uf from LCR-T4 meter.
            I found catalogue of samwha capacitor(samwha-catalogue_3.pdf file), which is attached to this thread,...
            06-02-2024, 07:31 PM
          • chth96
            What capacitor should I purchase for Power Supply of obsolete game consoles?
            by chth96
            hello.

            I have Sega Saturn and 5 years ago, I recapped all of capacitor in the Power supply, Because At that time, It frequently freezed black screen after SEGA logo displayed.

            It hardly ever freezed after I finished to recap all of caps in the power supply.

            But Yesterday, It did not show any screen at all and its green power LED constantly blinked.

            To my surprise I found that all of two NXH 10v 2200uf capacitors in the secondary area of Power supply have been bulged and It measured 57 mF and 75 mF capacitance.

            It seems that quality...
            10-01-2024, 08:14 AM
          • Loading...
          • No more items.
          Working...