Seisco RA-28 Control Board

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • GRowe
    New Member
    • Dec 2010
    • 1

    #1

    Seisco RA-28 Control Board

    This board has blown triacs and what appears to be caps. But when googling the part number I'm not getting an accurate part description or replacement suggestion. The markings read ( VRM .01k630v ). There are 4 on the board, next to the triacs, 2 are blown. I have found the triacs and ordered them but the blue caps or voltage regulators have me stumped . If any body can help with identifcation and suggest replacement parts my sister an brother an law would be grateful ( showers in 60 degree water is no fun from what I here ). Thanks ahead of time for any help.
    Last edited by GRowe; 12-24-2010, 10:24 AM.
  • ReverendJones
    Resurgam
    • May 2010
    • 49

    #2
    Re: Seisco RA-28 Control Board

    .01uf
    10% tolerance
    630 volt
    A pic would help but they sound like this: http://search.digikey.com/scripts/Dk...me=490-4822-ND
    Machina improba! Vel mihi ede potum vel mihi redde nummos meos!

    Comment

    Related Topics

    Collapse

    • Tynan Dill
      Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
      by Tynan Dill
      I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

      Upon bringing it home and plugging it up, it showed a standby light.

      I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

      The screen seems to blackout and stay black, but with a flashlight I can see the display.

      With my Playstation 4 connected via HDMI, and running a game I can hear sound.

      Assuming...
      11-22-2024, 01:46 PM
    • cmlewis89
      LG 47LB5DF blown power supply board
      by cmlewis89
      Hi folks,

      I'm new to this forum. So my trusty 17-year-old LG 47" LCD recently died. As I was booting it up, I heard a hum followed by a loud bang, sounds of pieces flying around, and loss of power to the unit. Inspecting the PSU, I saw two obvious problems: a blown thermistor (bang + flung pieces) and a visibly bulging main cap. Inspecting as many components as I could with my Fluke MM, I diagnosed that the following components on the "hot side" of the board were also bad: one of the 2 main MOSFETs, main 8A fuse, small cap (25V 47uF) connected to main caps, and a blown...
      09-03-2024, 07:50 PM
    • Yanleb
      LG 60PK550 Logic Control Board EBR63450301
      by Yanleb
      Hi all, I just want to share the repair of my 60PK550-UA TV set.

      The TV set was powering on, just no image. After verification, nothing wrong on the YSus or ZSus boards. Nothing wrong on the main board either.

      But I noticed that the LED was not flashing on the Logic Control Board. This is an EBR63450301. The LED is supposed to flash even with all the flat cables disconnected, with only the power cable attached.

      All the voltages measured at the electrolytic capacitors on the board were good. From top left to bottom right:
      C57: 3.30V
      C61:...
      07-20-2023, 12:38 AM
    • howardc64
      TCL 55S425 few horizontal lines, potential failure on both side of panel/buffer board
      by howardc64
      All left and right refers to looking from rear of TV (or looking from front with TV upside down)
      • TV came with vertical bars and no image. Found faulty TVS on left buffer board. Also replaced T-Con (may have damaged the original while hot air removing components, board has slight warp) and have full image but few horizontal lines on the screen. Some of the lines appears to be 2 pixel tall while others are 1 pixel tall.
      • Disconnecting left and right buffer board potentially reveals problems on both sides with different signals (unless this T-Con require jumper like Samsung FB_TRDY1&3) Fault
      ...
      Yesterday, 05:17 PM
    • sam_sam_sam
      Linear Garage Door Opener Control board took a crap install a new control board back normal
      by sam_sam_sam
      I have been having issues with this garage door opener for a while first the range of the remote was a lot less and sometimes it would start to go down and stop for no reason that I could find and would every once in awhile to start with then it started going more frequently until last Saturday when I opened the garage door it refused to close so I cranked up force all the way maximum limit this did not work also the sensor on one side that has a green and red lights that are supposed to be on when the door is open and there are no obstacles in the way on the original board the only light that...
      02-08-2025, 06:52 AM
    • Loading...
    • No more items.
    Working...