New Rework Station SMD 8508D+ Hot Air with 28L/min?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Kiriakos GR
    Banned
    • May 2012
    • 940
    • Greece
    #1

    New Rework Station SMD 8508D+ Hot Air with 28L/min?

    I am researching for Hot Air Rework Station this week, and just found that there is fresher models with higher power in watt and improved pumps with 28L/min than the usual 22L/min.

    The question is if some one can verify that those tools they do hide true performance?
    The most common practice is fake specifications just to attract consumers interest.


    http://www.ebay.ie/itm/Hot-Air-Gun-R...item27d7594932
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • shahnld
      wds-580 rework station issue
      by shahnld
      Good day.
      i received used bga rework station wds-580 which was not going above 300c despite the parameter was set to 350c, Everytime beeps at 300c so i did a factory reset and by mistake washed data and log etc. now the station boots to a white screen.

      Does anyone has a firmware for this station and want to share with me. i will really appreciate any help possible..

      kind regards...
      03-28-2024, 01:14 PM
    • minimania
      Need Schematic for jbc am6800 rework station
      by minimania
      hi all im looking for a Schematic for jbc am6800 rework station
      mine has stopped working fully
      it started with turning off when switched on then after a few off and ons it worked sort of for awhile
      now it wont turn on at all...
      01-28-2025, 03:44 PM
    • shahnld
      Seamark ZM-R6200 Rework station
      by shahnld
      Good day Experts.

      I have recently aquired a rework station SEAMARK ZM-R6800,. Is there anyone using this or some other similar station and give me some info about profile temp curve etc for removing leadfree soldered gpu chip..? just 1 profile will be enough to get started.

      Kind regards
      1 Photo
      01-24-2024, 10:55 AM
    • petemanuk
      Help with IR6500 rework station
      by petemanuk
      Hi,

      I been playing with a recently acquired IR6500 rework station and watching lots of YouTube tutorials to see how to use it with not much success. I’ve only recently joined badcaps but going through the forums there is a lot of knowledge here, so though it best is if I ask my question here.

      1. Firstly is the IR6500 any good for BGA rework or should I be spending my money on a better one.

      2. The instruction manual is pretty useless on explaining how to set the PID loops (no information at all!!) both top and bottom heater for th Kp, Ki and Kd...
      10-14-2022, 12:31 AM
    • Peter_1402
      Yihua 992DA+ Hot air gun and soldering rework station, burnt mark
      by Peter_1402
      Hi Everyone,
      I bought a Yihua 992DA+ hot air gun and soldering iron unit from a used market.
      1. Soldering iron works great
      2. There is a burnt mark on the hot air gun handle.
      I am a bit concern by the look of the melted plastic. I opened the hot air gun handle and took some readings with a multimeter.
      Heating element ~ 75ohm. (Similar reading taken from a spare heating element that came with the unit.)
      Thermocouple ~ 1.5ohm. (Similar reading from the spare heating element.)
      Reed switch tested ok with a magnet.
      From the above test, I can conclude...
      07-12-2025, 11:50 AM
    • Loading...
    • No more items.
    Working...