Look at this crap from Einhell ISG 1000/1 welder!! 
Attached Files
-
Last edited by Behemot; 11-01-2013, 02:40 PM.Less jewellery, more gold into electrotech industry!
Half of the computer problems is caused by bad contacts 
Exclusive caps, meters and more!Hardware Insights - power supply reviews and more! -
Re: Mother of holly crap, the bastard is just not giving up!!
Looks like it could have vented due to overvoltage and managed to survive the event, amazingly.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search. -
Re: Mother of holly crap, the bastard is just not giving up!!
Something on the secondary is shorted, either one of the fat TO-263 rectifiers (C16T20F) or the IB74 BKH transil (?). Primary seems fine, no shorts anywhere.
The question is if the cap blew because of overload or it blew before and because of voltage and current spikes on secondary the rectifiers blew than.Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts
Exclusive caps, meters and more!Hardware Insights - power supply reviews and more!Comment
-
Re: Mother of holly crap, the bastard is just not giving up!!
WOOOOOOOOW!
That sucker was blown HARD!
Could have been one of the diodes that shorted, putting AC through the capacitor, that would certainly make it vent like that.Muh-soggy-kneeComment
-
Re: Mother of holly crap, the bastard is just not giving up!!
Do not search for logical answers in a poorly designed circuitry with out a damn fuse.Comment
-
Re: Mother of holly crap, the bastard is just not giving up!!
It has fuse, even though on neutral (?!) instead of phase. But the primary seems OK, no rectifier or transistor blown there.
Problem is with secondary. I found this invertor was not really wery well rated by ppl. It is rated for 80 A, but being able to work only 15 % of time at 80 A output. No wonder, if you multiply 16 A (superfasts rating) by 5 (their number) you get 80 A but we all know it's not really how it works with diodes. Also the cooling system is weird, the diodes are soldered on PCB and the PCB itself is screwed to cooler. So the heat has to go through the PCB material first which is not really a good conductor!
If I will even succeed in contacting the owner (I got this thing here for so long I don't even remember whose it is
), I'll recommend him replacing the rectifiers with 30A schottkies from STMicro, they should have like 15 W less burned power and provide that 80 A for some reasonable time.
Last edited by Behemot; 11-02-2013, 07:25 AM.Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts
Exclusive caps, meters and more!Hardware Insights - power supply reviews and more!Comment
-
Re: Mother of holly crap, the bastard is just not giving up!!
This is very common with poorly designed inverters
http://ludens.cl/Electron/chinverter/chinverter.html
I call any watts figure on an inverter that poorly made "marketing watts".Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Mother of holly crap, the bastard is just not giving up!!
Seems the heat transfer is not that bad - I was hardly able to desolder the transil, which was bad, using 60W pen (the high-power one, no micro-crap) and 125W trnasformer pistol. Will have to resolder the output joint which I tore out, probably using hot air and two pens (60+80 watt)s because it is insane.
Any idea what the transil is?Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts
Exclusive caps, meters and more!Hardware Insights - power supply reviews and more!Comment
-
Re: Mother of holly crap, the bastard is just not giving up!!
Could it be caused by excessive ripple over time?
I know the capacitors in welders can be worked quite hard (frequent high charge/discharge rate).My first choice in quality Japanese electrolytics is Nippon Chemi-Con, which has been in business since 1931... the quality of electronics is dependent on the quality of the electrolytics.Comment
-
Re: Mother of holly crap, the bastard is just not giving up!!
Seems plausible. May it be 74 volts? This thing makes quite a low voltage (it is also known for being difficult to light arc with), around 40 volts so something like 75 votls transil may be just the right one.Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts
Exclusive caps, meters and more!Hardware Insights - power supply reviews and more!Comment
-
Re: Mother of holly crap, the bastard is just not giving up!!
I needed to heat that thing on a like 2000 watt cooker first to be able to do any soldering there. Was not able to heat it properly even using 80W soldering pen and I_don't_know_what_wattage soldering iron for gutters simultaneously. The latter gave up in the process…
Will now try to solder it together and see if it fires up. However, I don't have big caps enough, closes I have is Crapxon 420 uF/450 V and than only 390uF Rubycons…can only maybe squeeze a 100uF/400V KXG in parallel in there, somewhere…Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts
Exclusive caps, meters and more!Hardware Insights - power supply reviews and more!Comment
-
Re: Mother of holly crap, the bastard is just not giving up!!
It shorted immediatelly again going into protection mode, I am not wasting time with this thing any longer.Less jewellery, more gold into electrotech industry! Half of the computer problems is caused by bad contacts
Exclusive caps, meters and more!Hardware Insights - power supply reviews and more!Comment
-
Hi, my USB ports were hanging every now and then when starting up. So I decided to update the BIOS of the mother. Unfortunately, after finishing the flashing through QFLASH with a pendrive of the latest firmware version, the cooler turns on, black screen and seems blocked.
Model: GA-A320M-S2H (rev. 1.2)
Processor: AMD A8 9600
Previous BIOS version: F53
I downloaded the F58d version from here (I think it's the correct one)
https://www.gigabyte.com/ar/Motherbo...upport-dl-bios
Is there anything that can be done?... -
Need schematics for la-j662p mother board03-15-2023, 01:31 AM -
I am a new student.I am looking for repairing tools..What is the best multimeter testing mother bord -
I have been having issues with this garage door opener for a while first the range of the remote was a lot less and sometimes it would start to go down and stop for no reason that I could find and would every once in awhile to start with then it started going more frequently until last Saturday when I opened the garage door it refused to close so I cranked up force all the way maximum limit this did not work also the sensor on one side that has a green and red lights that are supposed to be on when the door is open and there are no obstacles in the way on the original board the only light that...
-
Hey all, I've been trying to fix a rx570 XFX XXX edition 8gb. Keep in mind I've no knowledge so I've been doing this solely using tutorials. Any help is appreciated.
8pin connector led is open when pc boots, but nothing else happens (no image).
Fans don't spin. Before the gpu broke completely, the fans used to spin at max rpm at the start and there were some wonky things happening in general, so it was probably defective already.
Everything below is based on this video: https://youtu.be/2Yz7HfzggYc?si=UM8VOndmqJX1gfgJ
PCIe pins are all ok. They have similar...
Comment