-
Never stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809 -
Re: Infinity PS-10 pictures and diagram
I have an infinity TSS Sub1200 subwoofer with the same type of plate amp and sealed module and it also has the same symptoms. It seems you have experience replacing the 4.7UF and 6.8UF capacitors plus you mention you modified the module with free sample power amp IC from National/TI instead. Which route do you recommend. I was also considering retrofitting with a dayton SA250.
-
Hi All,
I obtained a schematic diagram for the above mixer but I am wondering if a block diagram exists as I am trying to fix a problem in the protection circuit which I find a little confusing using a circuit diagram only. In the good old days the workshop manuals always had a block diagram with a circuit discription. Very useful for fault finding.
The protection light is perminently on. The right sode has a -80DC on the feed to the speaker, hence the protection led on. I have removed all the O/P transistors which checked out OK. I tested all other transistors in circuit which seem...07-31-2025, 01:35 PM -
Hello, colleagues!
I'm currently dealing with an issue while repairing a Concord Infinity elevator. The microcontroller P87C51SBPN used in the control board has failed, and I need the original firmware dump in .bin format to replace it with a new processor.
What I've done so far:
• Diagnosed the issue and confirmed the microcontroller is the root cause of the problem.
• The original processor is beyond repair, and I wasn't able to extract the dump.
• Reached out to the manufacturer (Savaria/Concord), but I haven't received a response yet.
...01-16-2025, 02:08 AM -
hello everyone, I'm looking for the wiring diagram of this led monitor.
the model is DHI-LM19-L200, but I think that any other diagram of a DAHUA monitor could be equivalent.
I really hope that among you someone can help me to repair this monitor, the screen is black, it doesn't seem like a backlight problem.
I see the presence of 12 volts, 5 volts, but without a diagram the repair is very difficult.
thanks to those who will answer12-10-2024, 04:37 PM -
Hi it looks like everything works don't know where to test except the 390v in the 2 capacitor in the hot side of the power supply and the weird 180v in the diodes in the cold side that should be discharged it is writin on the circuit no more you can read what is written on the circuit quite srrange color mixiing yellow and white
anyhow i couldn't t read anything else
the backlight is on strong and the screen does not get dark or very dark but no pictures
the mainborad feels a bit hott on the black part i test it to 52 degree's against 34 to 40 on the rest of it
... -
The 55" LG has been in the basement for a few months without being used. Turned it on yesterday, set came on as it should and showed a complete screen for about 5 seconds (was on a broadcast channel but no antenna was connected), then the screen went mostly dark with about 1/3 of the screen on the right lighting up with brighter lines in that lit part (sorry, no pictures of that). Power LED was cycling too, preventing the TV from fully powering up.
Pulled the back off, all boards looked OK. Pulled the LED connector, turned the set on to see if it would power up but I don't belive it...
Comment