Distributor inks agreement with high-voltage IC maker

PeteS in CA

Badcaps Legend

Join Date: Aug 2005

Posts: 3579

Country: USA, Unsure of Planet
#1

Distributor inks agreement with high-voltage IC maker

02-09-2006, 01:31 PM

Distributor inks agreement with high-voltage IC maker
Power Management DesignLine
(02/07/2006 9:31 AM EST)

Digi-Key Corporation announced today that it has signed a worldwide distribution agreement with Power Integrations, the leading supplier of high-voltage analog integrated circuits (ICs) used in power conversion. Digi-Key, one of the fastest growing distributors of electronic components in the world, currently ships product to more than 140 countries.

Why should anyone here care? PI's chips are used by many P/S mfrs, Delta for certain, for the +5V Stby regulator. Their IC looks like a TO-220 MOSFET or transistor, but it integrates the MOSFET with the controller. Now Digi-Key carries PI's products.

PeteS in CA

Power Supplies should be boring: No loud noises, no bright flashes, and no bad smells.
****************************
To kill personal responsibility, initiative or success, punish it by taxing it. To encourage irresponsibility, improvidence, dependence and failure, reward it by subsidizing it.
****************************
Tags: None

Previous template Next

20 year old Kenmore refrigerator ice maker bad water valve coil took a crap

by sam_sam_sam

I got lucky that when I got home and was about to get some ice out of the ice dispenser I hear and see water running down the outside of the ice dispenser what the heck is going on here

At first I thought that the ice dispenser mold was cracked so I brought a new ice maker because this one has been in there for about 10 years now

Well I put the new one in and wait and I wait for the water valve to open and let water in no such luck well there is a way to check the function of the motor and the water valve on this ice maker just need a jumper wire “L” to...
- Channel: Troubleshooting Appliances and other Household Electronic Stuff
04-09-2023, 08:04 PM
Ninja CM400C coffee maker not turning on

by ETx13

Pretty sure I know the answer to this but thought I'd ask here anyways. Got this nice coffee maker from someone since it just died on them. Long story short a surge blew a fuse and MOV in the power supply. I replaced both and tested, machine came back to life! Decided to try to take a video to show a friend and that's when I heard the relay click on and water start boiling in the tank and the display/buttons are now dead again. Did a bunch of testing, couldn't figure out why this is happening, every time I plug it in, the heater turns on via the relay. To try and test more things, I decided to...
- Channel: Troubleshooting Appliances and other Household Electronic Stuff
07-01-2024, 07:31 PM
DYMO Rhino 5200 Industrial Label Maker that the backlight does not work any ideas

by sam_sam_sam

I just bought a used one for a decent price for a used device it prints very nicely and clean and clearly so I am not going to complain about it but I would like to get it working again anyone have any suggestions on how to repair this back light

If I can not get the controller to work properly then I will probably have an external power supply for the backlight because it is difficult to see the screen without out it

One —>the LEDs might be bad
Two —> the buck converter or regular might be bad
Three —> the controller might not...
- Channel: General Electronics Technical Discussion
08-08-2023, 05:12 PM
Supermicro Server Power Distributor board

by shlomim412

Hello everyone

working on a supermicro server PDB
i attach a photo of how it looks

it suddenly died and the symptom is when pressing power on it sends a brief dc voltage and imediatly shuts down.
fan spins briefly and stops.

the power supply connected to it is working tested for sure (tested on another good pdb)

cannot find a short anywhere on the board, capacitors visually seem to be ok.
standby voltage is present (5v) also vdd to the power ic chip is present (also 5v).

any help would be apreciatted!
thanks...
- Channel: Troubleshooting Power Supplies and Power Supply Design
02-27-2025, 04:01 PM
Canon TR4540 dump (use PG-445 & CL-446 inks)

by dillies

Hi there.

Ink absorber full error on Canon Pixma TR4540. Any help will be greatly appreciated.
- Channel: Troubleshooting Printers, Copiers, Scanners and other Imaging & Printing Devices
07-04-2023, 04:29 AM
Loading...
No more items.

Distributor inks agreement with high-voltage IC maker

Distributor inks agreement with high-voltage IC maker

Related Topics