User Profile
Collapse
-
iPad 9 A2602 (820-2558) charging issue
Hi guys. I have a weird one with me today. iPad 9 A2602 (820-2558) could not charge properly because of a loose port, it would only charge if the cable was held in a specific position. The port was replaced, still did not charge. Replacing the Hydra IC remedied a short on the charging detection line. The iPad began to take charge but now we have new problems. Charges to 100% without issues and stops recognizing the charger being plugged in after (the battery charging sign goes away). When this happens it also does not connect to the PC for data connection etc. However, it functions normally (charging... -
Thanks, tried it 😢, didn't work. Same behaviour........ Now I'm more convinced that this isn't a BIOS issue. Do you know how / where I can check to clarify if this is actually a BIOS issue or hardware related.... -
Hey, here is my original BIOS. This is the one I believe is corrupted
ST: 81QF163
...Leave a comment:
-
I have one with a similar issue, however I do not have a boardview or schematics. Can anyone help me troubleshoot this issue. The machine has an initial 4W draw when plugged in, the keyboard lights up for about 5 seconds then the machine goes dead, no response from the power button, no fan spin etc. I've stripped the board of all connected components, tried with RAM sticks separately, tried with battery in and out, tried with both barrel and C port....the symptoms are the same. Without checking for proper voltages etc I (very stupidly) flashed a new BIOS to it but the issue remains. I can put...Leave a comment:
-
SMDFlea, sadly the one you provided didn't work either. Same symptoms. I think I'm going about this the wrong way.....Can anyone link me to the boardview / schematic for the LA-J372P Rev 1.0 (A00) board and guide me through the proper voltages and where I they can be found so I'll know for sure if it's a BIOS problem. The machine has an initial 4W draw when plugged in, the keyboard lights up for about 5 seconds then the machine goes dead, no response from the power button, no fan spin etc. I've stripped the board of all connected components, tried with RAM sticks separately, tried with battery...Leave a comment:
-
-
Lenovo Legion GO S, No Power (fixed), now no boot
Hey guys working on a Lenovo Legion GO S (8APU1).Owner said it suddenly stopped working during a short (30 minute or so) play session and was left for about two months. It's taking charge now from both type C ports without issue (93W then gradually declined as the battery filled). Constant amber on the charging led but no light on the power button led. I have no schematic or board view for this model so I'm basically working through pure electronics knowledge and experience. Long story short.....through thermal cam and voltage injection I was able to find a shorted cap and replace it with one...
-
MacBook AIR 1466 [ 820-00165-A] NO POWER, AMBER LED
HI, guys. Thanks in advance for all your help. I have a MacBook Air A1466 with no power. Removed and inspected the board there was corrosion near Q5150, cleaned it, replaced R5151 and R5152. Oddly enough there was no C5134 or R5153 on the no power board or the donor, go figure. F7140 was blown (no continuity), replaced it. C7377 was boiling alcohol so it was also replaced. Mounted to test..... No current drain, no fan spin, amber led on magsafe. F7140 is continuous. Checked both sides of F7140 for resistance to ground 1.5+ MOhms on both sides. PPBUS_G3H and PPVBAT_G3H_CHGR_REG on F7140 is 8.5V.... -
My gratitude goes out to you. This literally worked right out of the box! Fixed my "repeated-one-beep-no-boot" issue. Thanks so much. I hope your coffee is always as hot as you like it 😄...Leave a comment:
-
Hey, can you guide me through the process of doing the bios flash externally. I have the programmer and I'm not afraid to remove the bios chip or clip it on the board. I have the same machine. Sometimes it powers on and works flawlessly. Then other times its stuck with this beep beep beep continuously. Thee beep sound itself isn't a full beep either its more like the beep is cut....Leave a comment:
-
Thanks for the pointer. You have been a great at helping me understand what’s going on. I’m good at doing the work (soldering etc) but I’m not adept and understanding the circuits. Where do I check that I have enable and that it is good? I did the jumper anyway but still no backlight and still the same 8.6V @ D7701 and C8317. Please confirm if the jumper was done correctly....
Leave a comment:
-
The SSD is out so I’m unable to confirm the login screen but I have tested to see the blinking ? folder on screen. I have two screen. It’s highly unlikely (although possible) that both are bad.
How can I confirm that U7701 is functional (where can I probe for input and output voltage)?...Leave a comment:
-
Can anyone help me identify theses iPad Pro 11" (A2759) capacitor values
Working on an iPad Pro (A2759) with no touch. These components highlighted are shorted near one of the screen connectors (I'm assuming its for flex cable that handles touch). Can anyone help me with their values (C379, C1106 and the big one has no label). Please see attached picture. Any help greatly appreciated. Thanks in advance.
... -
Macbok Air A1466 820-3437-B Backlight issue (Help needed)
Hey guys anyone available to help me with a MacBook Air A1466 Backlight issue. Board 820-3437-B. So far I've checked the fuse (F7700) and it's good, checked C8317 (big cap near LVDS) and with load (Screen connected) I get 8.6V). The history is it suddenly stopped working. My knowledge is very limited but I do have some tools and I as always I am willing to learn. Thanks in advance... -
As far as I can see there is one DC IN MosFet. I checked it in Ohms mode.
Gate to source 435 ohms
Gate to drain 436 k
Drain to source 1 ohm
Just to clarify...please let me know if I am wrong. The gate is the single pin, source are three pins next to it (same side) and the drain is on the other side right?Leave a comment:
No activity results to display
Show More
Leave a comment: