Samsung ue49mu6120

[lotas]

NO lotas.... pin 9 on black one.. no need to connect at all.. even remove C or add R no need too.... just VCC bridge it to 3.3v to protect spi eeprom if they cant handle 5 V... again only the black ONE samre to post photo # #441 with out any add of r or cut rail

Open the datasheet on CH341A and look at 9 pin if you switch to 3v power supply. In the circuit for modification, there is no need to remove the capacitors, but replace them with tantalum of higher capacity.
https://4pda.to/forum/index.php?show...st&p=125980884

[Diah]

If you completely switch the programmer to 3.3v power supply, then 9 pin is connected to 3.3v (there is absolutely no need to install a jumper for 5v power supply!)
https://vil2.livejournal.com/780.html

NO lotas.... pin 9 on black one.. no need to connect at all.. even remove C or add R no need too.... just VCC bridge it to 3.3v to protect spi eeprom if they cant handle 5 V... again only the black ONE samre to post photo # #441 with out any add of r or cut rail

[lotas]

I am attaching the contents of the video eprom.
Unfortunately I can't find cards for 40'' at the moment.
Thank you for your time

What panel do you have, number CY-xxxxx? And the full model number of your TV.

[lotas]

this diagram old version of the programmer... the black one only need the vcc to move it to 3,3V.. that's all . i have one just have this modifying of VCC,, no need connect it to pin 9 other wise it will be short circuit on the black one

If you completely switch the programmer to 3.3v power supply, then 9 pin is connected to 3.3v (there is absolutely no need to install a jumper for 5v power supply!)
https://vil2.livejournal.com/780.html

[toptib]

There are also positional resistors on the board for different sizes of diagonals, it’s better to look for ones with the same diagonal as yours. You can read the dump T-con (25Q80), there may also be a problem with it and post it here, I’ll take a look and write down the panel number.

I am attaching the contents of the video eprom.
Unfortunately I can't find cards for 40'' at the moment.
Thank you for your time

[Diah]

But everything is clearly drawn in the diagram, remove the ceramic capacitors, put tantalum capacitors in their place (the capacitance is written in the diagram), the resistors are placed in the gap (the tracks are cut).

this diagram old version of the programmer... the black one only need the vcc to move it to 3,3V.. that's all . i have one just have this modifying of VCC,, no need connect it to pin 9 other wise it will be short circuit on the black one

[lotas]

Hi Lotas,Do you know if I mount a UE55MU6400UXTZ on my tv UE40MU6400UXTZ can I change the panel on the service menu?

There are also positional resistors on the board for different sizes of diagonals, it’s better to look for ones with the same diagonal as yours. You can read the dump T-con (25Q80), there may also be a problem with it and post it here, I’ll take a look and write down the panel number.

[toptib]

If the panel is 100% working, then you can install another motherboard (and hope that the motherboard will also work).

Hi Lotas,Do you know if I mount a UE55MU6400UXTZ on my tv UE40MU6400UXTZ can I change the panel on the service menu?

[lotas]

Some doubts:
Should C1 and C2 be eliminated, and should the tracks be connected or left open?
Is there any connection to be broken beyond contact 28 of CH341A ?

But everything is clearly drawn in the diagram, remove the ceramic capacitors, put tantalum capacitors in their place (the capacitance is written in the diagram), the resistors are placed in the gap (the tracks are cut).

[Salvocchio]

Yes, above is a diagram with modifications to the power supply (blue, don't forget about 9 pin) and the addition of resistors.

Some doubts:
Should C1 and C2 be eliminated, and should the tracks be connected or left open?
Is there any connection to be broken beyond contact 28 of CH341A ?

[jellytot]

hello

[Salvocchio]

Country: Cagliari?? Italy...

Yes

[Davi.p]

Country: Cagliari?? Italy...

[Salvocchio]

Some doubts:
Should C1 and C2 be eliminated, and should the tracks be connected or left open?
Is there any connection to be broken beyond contact 28 of CH341A ?

[lotas]

Yes, above is a diagram with modifications to the power supply (blue, don’t forget about 9 pin) and the addition of resistors.

[Salvocchio]

Basically, should I make the two changes?

[lotas]

WARNING: If the /WP or /HOLD pins are tied directly to the power supply or ground during
standard SPI or Dual SPI operation, the QE bit should never be set to a 1.
To correct this drawback, you need to disconnect the legs #WP (pin 3) and #HOLD (pin7) from VCC
and connect them to VCC through 4.7 kohm resistors.

[Salvocchio]

Sorry Lotas. My programmer is the one in the attached picture. What are the improvements I need to make to make it work better?

[Salvocchio]

Thank you. i'll try

[lotas]

Hi Lotas. Thank you for the valuable support you provide.
I have the same problem with my Samsung UE40MU6400UXTZ.
Unfortunately, I lost the original DUMP.
I purchased a new W25Q40CL, can you help me in any way?
My programmer is CH341A.

Hi, well, without the original dump, how can I help you, the only option is to select one for your software version, in this thread I posted a lot of corrected dumps, select one (make some kind of adapter, so as not to unsolder and solder each time to check)
Let me add that the diagonal is not important here, it can be any number, and any four-digit number will also work, that is, look for any dump Ux xxMUxxxx.