PN64D7000 Picture Issues

Collapse
X
Collapse
+ More Options
Posts
 
  • Time
  • Show
Clear All
new posts
  • slipstreamelectronics
    New Member
    • Nov 2019
    • 3
    • United States

    #1

    PN64D7000 Picture Issues

    Hey All!
    I have a PN64D7000. I love this tv and it died a couple years ago and has been sitting in its box until I have some time to look at it. That time has came, and I opened it up. I decide to replace all but the main board after I was getting some power anomalies. Everything powers up but the tv will not display a picture and keeps cycling. I went to test the display by using a jumper on the main board power connector, disconnected the main ribbon to the logic board and use a jumper on the top pins. The tv powered up and I saw the screen flash real quick as it does when the tv powers up normally. I still did not get a test pattern.

    At this point I am scratching my head. I did see the panel has lower buffer boards "x3". Do these have any serious relevance to the tv operation or they just more or less a pass though buffer like the x-main buffer.'

    All the power levels on the x-main, y-main, and power board are correct. The logic board LED is blinking about once a sec which from my research is correct. I did follow the steps laid out in this video which looks to be the same model.
    https://www.youtube.com/watch?v=JjrwTZC5nVg

    Can anyone give me some insight of where to look now. I like this tv which is the reason I am trying to repair it. I have several OLED and other monitors but I do like this and the kids like it as well for the 3D functions.

    Thanks Guys!
    Last edited by slipstreamelectronics; 11-13-2019, 05:36 PM.

Related Topics

Collapse

  • JJAAMM
    SAMSUNG UN55KS9000F picture fades then distorts into vertical lines after 20 seconds
    by JJAAMM
    This was my main TV for the last 6 years. I'm not inclined to throw out a $2600 TV so quickly so I'm trying to investigate the issue.

    Problem
    TV was disconnected from power for 6 months during construction. When I plugged it yesterday picture was fine, after 30 seconds it dimmed then started developing horizontal lines, picture then starts to ghost vertically until it degrades into vertical streaks. TV always displays a perfect picture when cold. I can unplug TV for 5 minutes and plug it back in and picture is restored for 20 seconds. I can also keep it in standby mode...
    07-06-2023, 06:01 AM
  • homerging
    Sony trinitron Wega KV-HR36 picture issues
    by homerging
    Hello,
    could anyone please tell me what is likely to be causing the CRT picture quality issues as shown in the attachments and what it'd take to fix it if that is possible?

    The picture has a greenish tinge, colour scan lines are separated and there can be shimmering and the bottom can be missing at first. It has slowly gotten worse over time.

    It is worst when first turned on and slowly improves but not resolves over a period of approximately 90 minutes. Warmer room temperatures possibly have a positive influence....
    08-05-2022, 07:06 AM
  • TR103
    Samsung TV model UE50TU: rebooting, backlight, sound, but no picture
    by TR103
    Hi, I have a Samsung UE50TU with:
    - sound and backlight, but no picture
    - when it arrived, it had a picture for a few seconds
    - it keeps rebooting
    - without ribbon cable between the two panel boards, it does not reboot but I have no picture
    - without cable between mainboard and lcd panel, it does not reboot (but obviously i have no picture)
    - when i try a tape fix, its keeps rebooting, unless I tape off pin 1 (the innermost pin). In that case it does not reboot but I have no picture.

    - without cable between mainboard and lcd panel and with a jumpered...
    01-22-2025, 04:12 PM
  • howardc64
    A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
    by howardc64
    Problem

    This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
    08-04-2024, 10:36 PM
  • Mgiffune
    Samsung UN60EH6000F Black Screen, Backlight and Sound Good. Power Cycle Returns Picture
    by Mgiffune
    I have a 60 inch Samsung UN60EH6000F flatscreen TV. The screen went black a few months ago Sound is good, backlight is good, no menu. I replaced the TCon board with a used board purchased from Ebay. It worked fine for a 3-4 months, then the screen started ‘fading' back. Once again, sound is good, backlight is good, no menu. However, this time the picture looks fine for about 10-15 minutes, then fades back. If I power cycle the TV, the display reappears, for another 10-15 minutes, then fades black again. Repeatable ever time.

    I ordered a supposedly ‘new' Tcon board this time, and
    ...
    06-09-2024, 10:28 AM
  • Loading...
  • No more items.
Working...