LG 55EC930V OLED - 3 Second Power No Display

[freakaftr8]

Re: LG 55EC930V OLED - 3 Second Power No Display

The reason you're getting a dim picture is because DRV_ON is enabled. However there is no data being fed to the panel. The fact that you don't have any white vertical lines Is a good sign because these OLED'S love to burn vertical tabs.

Those buttons that are on the main board do a reset of the tcon, And the other resets the TV as if you were to unplug it and plug it back in.

The system is very finnicky and super sensitive to any over voltage condition of the panel. If it recognizes a gate failure it will shut down. It will attempt to restart 2 consecutive times before a lockout condition occurs. This is sensed by T con board. You're no picture is most likely and invalid T con board with a wrong panel ID number for the panel. (This happened to me until I installed the OEM tcon back in.) Also if the tcon came from a smashed panel it could have shorted blowing a fuse or an inductor.

[Diah]

Re: LG 55EC930V OLED - 3 Second Power No Display

you need now to start from beginning trouble shooting. but after you put all changed you did before such-

1- put the original Main board , put the original T-CON driver. then turn on and see the result same as the photo you posted before. use your app to press Menu to see if there OSD come out . also freakaftr8 suggested feed it with signal like blue ray at HDMI IN which labeled with ARC so the TV will switched to this input.

[freakaftr8]

Re: LG 55EC930V OLED - 3 Second Power No Display

Btw. Try your original tcon.

[freakaftr8]

Re: LG 55EC930V OLED - 3 Second Power No Display

By the way guys sorry I haven't been on the forums lately. I really have a lot on my plate these last few years..

[freakaftr8]

Re: LG 55EC930V OLED - 3 Second Power No Display

So the LG logo is staying lit without any jumpers in place? It seems to respond by pressing volume up volume down and input buttons? I can see you are getting some kind of a picture can you put something into an H DMI port to produce sound or go to TV mode to produce static sound?

Also is the TV shutting down after a period of time going to the blink cycle?

This particular set up if not getting acknowledge that everything is systems go then after 3 consecutive power UPS it will go to the lockout

Sorry for the PM.. Didn't realize you were in the UK

[Billsy]

Re: LG 55EC930V OLED - 3 Second Power No Display

Ahh I see. Yes after initiating power only mode the power will stay on and if I unplug then plug in, it will power again.

Trouble is, I can't get any further than the partial dim screen. It doesn't respond to any remote comands

Thanks

[Diah]

Re: LG 55EC930V OLED - 3 Second Power No Display

Diah sorry but how can you tell it was going into STB mode?
Whats SM? Safe Mode?

Apologies but I don't understand the second part of your post.

Thanks for your help tho I really appreciate it.

BR

this TV before you received it was at STB mode before they plug it out from wall socket..each time you was try to plug it on.. it goes to the last state -- your case was STB... this option at all TV can be changed at SM service menu.

also when you turn it on with IR that's enough it will turn on always after you plug it at wall socket

[Billsy]

Re: LG 55EC930V OLED - 3 Second Power No Display

Diah sorry but how can you tell it was going into STB mode?
Whats SM? Safe Mode?

Apologies but I don't understand the second part of your post.

Thanks for your help tho I really appreciate it.

BR

[Diah]

Re: LG 55EC930V OLED - 3 Second Power No Display

also your TV was going to STB mode after you plug it at wall socket AC. as its in SM as original set to remember last state.
now when it is on don't turn it off with IR. keep it so easily, also i assume your Original T-CON will have same way to show on your panel. so its not as you tilled 3 Second Power No Display

[Billsy]

Re: LG 55EC930V OLED - 3 Second Power No Display

Ok so I pulled the tcon from the cracked set, loaded it into the other set and no change.

After hours of pi55ing about with IR leds and headphone cables trying to make a IR blaster, found an old galaxy tab in a cupboard with an IR blaster built in. Anyway long story short, using the RCoid app, I was able to send the Power_Only command and the TV powers up. The screen is very dimly lit kind of across lower left corner. I'm guessing this is now out of lock out mode but this is as far as I can get. The only other thing. There are two buttons on the main board. Does anyone know the procedure to bring it back to life or am I wasting my time?
Many thanks

[Billsy]

Re: LG 55EC930V OLED - 3 Second Power No Display

I just got an identical set for £80 on ebay with a broken screen. This should be fun!

[Billsy]

Re: LG 55EC930V OLED - 3 Second Power No Display

if i am i will change this board.

Yeah maybe I'll look out for a replacement board.

[Diah]

Re: LG 55EC930V OLED - 3 Second Power No Display

Evss_con_ out
From different angle

this LG suffer from Panel burned image, because of the discharge problem, and this parts i mentioned its belong to discharge, to me its over heated .. let hear other opinion

[Billsy]

Re: LG 55EC930V OLED - 3 Second Power No Display

Evss_con_ out
From different angle

[Diah]

Re: LG 55EC930V OLED - 3 Second Power No Display

if i am i will change this board.

[Billsy]

Re: LG 55EC930V OLED - 3 Second Power No Display

Here's the back side

[Diah]

Re: LG 55EC930V OLED - 3 Second Power No Display

EVSS_CON_ out driver IC burned

[tom66]

Re: LG 55EC930V OLED - 3 Second Power No Display

Could you take a picture of the bottom side of the board? Curious about something.

[Billsy]

Re: LG 55EC930V OLED - 3 Second Power No Display

[Billsy]

Re: LG 55EC930V OLED - 3 Second Power No Display



Rest of pics are rotated by the forum for some reason.













Thanks guys