FE3407F Alternative ?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • mmartell
    Badcaps Legend
    • Oct 2013
    • 3189
    • Canada
    #1

    FE3407F Alternative ?

    I have here an LG 50PG20 with the common buffer board failure. This board uses the FE3407F scan ic but I don't have any here. I removed a Renesas R2A20299FT from a different LG buffer board and soldered it in place. The result is I have a full raster but no image in this portion of the screen and a black line somewhere in the middle a few pixels wide.

    I've checked and rechecked and resoldered the chip a few times always the same result.

    Does anyone know with certainty if these ic's are compatible ?
    Tags: None
    • mmartell
      Badcaps Legend
      • Oct 2013
      • 3189
      • Canada
      #2
      Re: FE3407F Alternative ?

      I ordered a couple of FE3407F ic's from the bay and after installation the tv is back to normal.

      Conclusion - these two ic's are NOT compatible.
      Attached Files

        Comment

        Previous template Next

        Related Topics

        Collapse
        • howardc64
          A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
          by howardc64
          Problem

          This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
          08-04-2024, 10:36 PM
        • howardc64
          TCL 55S425 few horizontal lines, potential failure on both side of panel/buffer board
          by howardc64
          All left and right refers to looking from rear of TV (or looking from front with TV upside down)
          • TV came with vertical bars and no image. Found faulty TVS on left buffer board. Also replaced T-Con (may have damaged the original while hot air removing components, board has slight warp) and have full image but few horizontal lines on the screen. Some of the lines appears to be 2 pixel tall while others are 1 pixel tall.
          • Disconnecting left and right buffer board potentially reveals problems on both sides with different signals (unless this T-Con require jumper like Samsung FB_TRDY1&3) Fault
          ...
          07-24-2025, 05:17 PM
        • Yanleb
          Schematic or datasheet for Plasma TV buffer chip
          by Yanleb
          Hi all,

          I'm interested in understanding how a buffer board chip is working. I know there's about 90 outputs per chip to the plasma panel, but I'm more interested to know about the input pins. I guess that some of them are address pins, but I want to know more.

          So far I've found nothing at all. I haven't found any datasheet about the various buffer chips, and I haven't found any schematic for the buffer board using them (Y Buffer Board in Samsung's terminology).

          Any information will make me happy. It can be from any buffer chip or plasma TV manufacturer....
          05-18-2022, 01:36 PM
        • legg
          LG 42PC3 buffer output doesn't follow YSUS
          by legg
          LG42PC3D -UD originally with green lamp but no display or audio.
          Owner says was working, then went 'pop'.
          All 5V caps bulging. replaced.
          All PSU output voltages within spec but -Vy is low on YSUS.
          One of three parallel fets between SUS_OUT and SUS_DN is zenering,
          eventually shorts DG. Replaced all 3 - -Vy now OK.

          Y scan buffer test point does not follow YSUS output below -50V

          Note: This unit seems to expect YSUS output to park at -Vy in between
          drive signal pattern periods. A replacement drive signal board confirms this....
          11-18-2021, 11:49 AM
        • howardc64
          Samsung QN75Q6FNA backlight no display, red LED blink 2x, fault in panel
          by howardc64
          • Prior owner tried a replacement main board. No difference.
          • Samsung 2x red blinking standby LED = panel fault
          • Jumpered FB_TRDY_1 (pin 1 CN1300 left. main tcon->left side buffer boards) and FB_TRDY_3 (pin 95 CN1301 right. main tcon->right side buffer boards) This allows testing individual T-Con (on main board) connection to panel on this Samsung. Found fault on left side (viewing from rear of TV)
          • Each side has 2 buffer boards, disconnected left side flex between 2 buffer boards. Fault is on the left most board.
          • Tape masking eventually isolated to CN1300 pin 15 (CKV4_GOA) Display
          ...
          07-19-2025, 10:54 PM
        • Loading...
        • No more items.
        Working...