Vizio E472VL flash memory eeprom firmware?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • kevinm34232
    Badcaps Legend
    • May 2012
    • 1884
    • USA
    #1

    Vizio E472VL flash memory eeprom firmware?

    Anyone doing these? Need:

    VIZIO MODEL # E472VL

    1 PROGRAM H27UAG8T2BTR FLASH MEMORY CHIP WITH E472VL FIRMWARE

    P/N: 3647-0462-0150

    BOARD P/N: 0171-2272-3923
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • zoltor
      Canon G3430 has a lightning flash after the firmware
      by zoltor
      Good afternoon. The Canon G3430 is lit by lightning after the firmware, it does not respond to the buttons. I did not flash it, they brought it with traces of soldering, and all three chips. SPI - IC401 25Q128, IC402 25Q32, IC403 M24128. The SPI flash drives may have been confused in places. The QM8-0985 formatter. I've tried all the firmware available on the Internet, and the result is the same. I ask you to send dumps of chips, if someone has the same revision of the board, also tell me if the location of the SPI flash corresponds to the position numbers. Thank you very much in advance.
      09-17-2025, 12:40 AM
    • karlox
      Request for EEPROM Firmware Backup – Epson PowerLite S18+
      by karlox
      Hello everyone,
      I have an Epson PowerLite S18+ projector in the workshop showing signs of a firmware fault. I’ve checked all voltage lines and signal paths, and everything seems within normal range.

      Here’s the issue: when the power cable is connected, the power LED immediately turns blue even though the projector doesn’t start. When powered on, the fans run but the lamp never ignites. After a few minutes, both the temperature and lamp indicators turn red.

      I’m attaching the backup I read from the IC in case it’s useful for analysis or comparison.
      If anyone...
      10-16-2025, 07:48 PM
    • edgarmg15
      Damaged EEPROM on TV Vizio E320-A0
      by edgarmg15
      Hi everyone

      I´m trying to repair a TV Vizio E320-A0 that I found in the street

      The symptoms are it doesn't respond with remote or buttons, the LED indicator is always off and also there is no image on the TV.

      The power supply board works fine (I probed the terminals with my multimeter) but in the main board the EEPROM doesn't works correctly because the voltage on the pins doesn't match with the parameters of the datasheet.

      So, I´m going to replace the EEPROM with a new one, but the problem is that my programmer (CH341a)...
      11-19-2022, 03:46 PM
    • corrize
      Nikon D800 camera - flash don’t work and capacitor don’t charge
      by corrize
      Hello, I'm stuck in troubleshooting…
      The flash system works like that : when the (mechanic) flash button is pressed, the flash mecanically pop up, and a circuit buck boost elevate 7v (batt) to 200-300v (?) for charging the big capacitor. And when the photo shoot button is pressed, the capacitor is discharged in the xeon light.

      In the D800, there is a first « power board » close to the battery. 2 wires (batt 7v) goes to another little « flash board ». I measured 7v, so ok.
      When I press the flash button, it's detected by the system, flash icon appear on LDC display....
      10-01-2022, 10:02 AM
    • NSkyLab
      Toshiba 55SL417U looking for EEPROM and Firmware
      by NSkyLab
      Hello everyone, I described the symptoms and measurements here
      It seems I tried everything, my last idea is that the eeprom or firmware (or both) may be corrupt.
      I'm not able to find eeprom and firmware dumps in open sources.
      Hoping someone here has access to closed forums or manufacturer's service center resources and can help get those dumps?
      01-20-2023, 12:29 PM
    • Loading...
    • No more items.
    Working...