Request for EEPROM Firmware Backup – Epson PowerLite S18+

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • karlox
    Senior Member
    • Dec 2017
    • 138
    • México
    #1

    Request for EEPROM Firmware Backup – Epson PowerLite S18+

    Hello everyone,
    I have an Epson PowerLite S18+ projector in the workshop showing signs of a firmware fault. I’ve checked all voltage lines and signal paths, and everything seems within normal range.

    Here’s the issue: when the power cable is connected, the power LED immediately turns blue even though the projector doesn’t start. When powered on, the fans run but the lamp never ignites. After a few minutes, both the temperature and lamp indicators turn red.

    I’m attaching the backup I read from the IC in case it’s useful for analysis or comparison.
    If anyone has a working firmware or EEPROM dump for this model, I’d appreciate if you could share or sell it.

    Thank you for your time and help.
    Attached Files
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • Kolecki
      Epson et-2756 Firmware dump file
      by Kolecki
      Hi I need bios or firmware dump file to printer Epson et-2756. Can you help me. My printer is bricked in printer mode and i need reprogram chip on board
      01-18-2025, 11:38 AM
    • NSkyLab
      Toshiba 55SL417U looking for EEPROM and Firmware
      by NSkyLab
      Hello everyone, I described the symptoms and measurements here
      It seems I tried everything, my last idea is that the eeprom or firmware (or both) may be corrupt.
      I'm not able to find eeprom and firmware dumps in open sources.
      Hoping someone here has access to closed forums or manufacturer's service center resources and can help get those dumps?
      01-20-2023, 12:29 PM
    • robante15
      Epson PowerLite Presenter L 3 Red LED's Flashing
      by robante15
      Hi, I have an old Epson PowerLite Presenter L.

      I have the following problem, when I turn it on it starts up normally, the image works correctly, after a while (it can be a couple of minutes, up to hours) it turns off and the 3 LED lights flash red (Temperature, Lamp and Power).

      The 5 fans included in this equipment work correctly, I maintained them and verified their correct operation.

      I also read somewhere else that it could be caused by cold solder on the connectors, so I put new solder on them and the problem persists.

      I can't find...
      10-23-2023, 08:01 PM
    • zklgfs
      Anker SoundCore 2 Bluetooth Speaker Turns Off After a Few Seconds (Possibly Firmware Issue?)
      by zklgfs
      Hi,

      I have an Anker SoundCore 2 (A3105) that I saved from the trash (well, I guess there's a reason why it was supposed to go into the trash...). The problem is that it always turns off after a few seconds (sometimes it stays on a bit longer, between 30 and 60 seconds, but it still turns off). The power light turns on and the bluetooth light starts blinking, but both abruptly turn off again. The "turn off sound" is still played after the lights turn off. Sometimes, it also loops the on-off cycle several times without me pressing any buttons. If I connect an AUX cable, music...
      08-11-2025, 02:14 PM
    • SidneyCanadas
      93C46 and 93C56 EEPROM
      by SidneyCanadas
      I tore apart my instrument cluster for my 2008 Toyota Corolla made in 2007 in Cambridge, Ontario, Canada and pcb location: IC6=EEPROM is a surface mounted device with part # of 93C46W7, some claim the EEPROM out of a Camry part # 93C56 will allow odometer to roll over 299 999 KM or miles. The data sheet for both is below:

      https://cdn.badcaps-static.com/pdfs/...c6e42b20d3.pdf 2

      Anyone know if the Camry one will work on my Corolla?. And which EEPROM reader/writers do you all recommend I purchase that will allow me to read the old values of the old...
      06-14-2023, 01:16 PM
    • Loading...
    • No more items.
    Working...