Westinghouse DW39F1Y1

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Bitgod
    New Member
    • Dec 2016
    • 2
    • United States
    #1

    Westinghouse DW39F1Y1

    Borrowing a pic image someone else took but same TV.



    How do I know what the voltages should be for CON 1 2 3 and 4?

    TV is black screen but with audio.
    Tags: None
    • dick_barton
      Badcaps Legend
      • Aug 2015
      • 6643
      • Wales
      #2
      Re: Westinghouse DW39F1Y1

      Do you have any photo's Are the voltages expected printed on the power supply circuit board alongside or close to the connectors?

      Edit
      Photo arrived while posting
      Con 6 shows 12V, GND, EN_??
      Is there a crack in D105?
      Capacitor close to the Led output is 100uF, 100v rating so would expect 80-85v
      Last edited by dick_barton; 12-03-2016, 01:41 PM.
      Willing to help but I'm no expert.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • Capacitorial
          Powersupply has all the voltages - Monitor still no power
          by Capacitorial
          Hello guys,

          I have a Philips 240B7QPJEB. The monitor seems completely dead.
          I opened it and measured the voltages of the powersupply. I found that a mosfet was dead and replaced it.
          On the connector, that goes to the TCON board, all voltages 15-19V and 5V are present.
          The small connector on the left of the PSU has two cables with 18V and all the other have 0.2V. It connects on this small connector on the left ontop of the panel. I guess the backlight? Seens fine I guess.
          The weird thing is, that the Power LED is powered over the TCON board.
          On The TCON...
          12-28-2024, 02:12 PM
        • flibidy
          Magnum IA.100 Amplifier Switches on, No Output, Possible Input Side fault?
          by flibidy
          I have here a Magnum IA.100 which belongs to my parents.



          The unit powers on & when the relay kicks in, you get a pop from the speakers (this might sound weird but is usual behavior for this amp). However, you get nothing coming through it from any of the inputs & no pops and crackls from any of the controls.


          Because of the sound from the speaker when the amp turns on I have assumed that the output section probably works but I could be wrong & I'm not sure how to test that side of things further.


          What Ive done........
          Magnum IA.100 Front
          8 Photos
          01-01-2025, 01:26 PM
        • RossMoodley1967
          HISENSE LCD LED TV MODEL HX40N2176F LED DRIVER SN51DP IC PINOUT AND VOLTAGES
          by RossMoodley1967
          Hello

          Need to know the voltages that will be present on SN51DP ic when tv is in standby and when powered on.

          Just to elaborate on the problem with the tv 1.set came in with flash of HISENSE logo on screen then back into standby.2. Now tv when plugged in red standby light present to quickly changes to blue but no backlights.3.Then an hour ago i checked again , came on standby and stayed until i pressed the power button which changed to power on (blue)4.As far as the led driver circuit goes voltage at output in standby was 38v , power on led light up voltages rise 58v-68v...
          03-01-2024, 06:07 AM
        • karlp028
          MSI Z390-A PRO missing VCORE voltages
          by karlp028
          I've got an MSI Z390-A Pro motherboard that starts up fine, but it's missing the VCORE (and VGT) voltages. All of the other voltages are present (e.g. VCCSA, VCCIO) and I know the CPU (i7-9700k) is good. Now, the original PWM controller (UP9521P) had an internal short and I replaced it with a new one. All of the enable signals look good. The problem seems to be the PWM signals going to the MOSFET drivers. I checked them with an oscilloscope and they are all flat 1.5V with no pulses. I don't know why this would be and I'm not sure where to look next.
          06-23-2025, 01:25 AM
        • lol999
          Asus Prime x299 Deluxe - no VCCIO VCCSA voltages
          by lol999
          Motherboard after starting show Q code 00.
          No shorts on any rail ( at last I can't finde any)
          All voltage are correct on SIO - 3.3V, PCH power 1V , DDR 1.2V, SPI 8 leg 3.3V
          Nothing get hot, PSU starting, all lights came ON....
          One thing i can see incorrect is no VCCIO and VCCSA voltages and no main power on CPU.
          After deep looking I found dead Synchronous Buck converter CSD97374Q4M that is powering VCCIO for CPU but after replacing it nothing changed. Voltages on it are correct....
          This buck converter is PWM'ed by Asus DigiVRM ASP1405I-62T. Can't finde any datasheet...
          01-21-2024, 02:25 PM
        • Loading...
        • No more items.
        Working...