Hitatchi PDP50X3R010

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • MSteinmann
    New Member
    • Nov 2014
    • 2
    • USA
    #1

    Hitatchi PDP50X3R010

    Good morning. I have one of those very heavy, and I'm afraid very dead electric parts caskets. The unit was running, it went dark and silent. After approx. 2 minutes I could hear a relay clicking. As any self respecting physician of the electrons would do,,,, I open her up. I did find a relay click, and the dreaded hummmmmmm that goes with it. I also found two ceramics plates completely across the board that her very hot. Ok there you have it, hoping that somewhere, someone has already seen these symptoms.

    Thanks much!
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • jm1234
      9V relay temperature 40C
      by jm1234
      Hi, I'm seeing one 9V relay having temperature 40C on its 9V (primary) side. Does that seem right? I switched 2 relays on that board and the temperature was the same (on the same position), so I'm sure it's not a faulty relay. I measured voltage on that relay and it was 9.5V DC, so that looks good. I don't see any other relay on that board having that kind of temperature and they have 9V on them too.
      I thought maybe the transistor that is switching this relay keeps switching on/off, so I also checked for AC and there was almost none: 0.3V using mV range. No steady frequency was shown, but...
      05-09-2024, 03:03 AM
    • edugimeno
      Biomass Boiler not driving cleaner motor relay. ENERTRES BIOMASA BI-650
      by edugimeno
      Hi everyone!
      I have this board that suddenly stopped supplying power to an output that drives an interchanger cleaner motor.
      I checked while the board was in place with all wires attached and there's no AC voltage on the corresponding plug X5
      This X5 is driven by fuse F8 (tested OK) which comes from the second orange relay
      To make sure there are no charcoaled contacts inside the relay, I got a 24VDC power supply and got it ready to manually power up the coil side of these relays.
      I respected the polarity, positive to cathode of protecting diode
      So provided all...
      04-18-2024, 01:15 PM
    • sam_sam_sam
      Mitsubishi CNC switching power supply board dead / relay board bad diode failure
      by sam_sam_sam
      I was working on this CNC machine today found no keyboard functioning no control relay powering on
      The screen powered on and was giving an operation error but the manual was not very clear about what the error exactly was but with a little bit of troubleshooting and finding out that the control relays not powering on and no keyboard functions we narrowed down to this one switching power supply which of course does not have any indicator LED light they are on the keyboard interface/relay controller board

      Found shorted diodes on main controller relays there are 3 of them that...
      01-07-2023, 05:43 PM
    • fadi90
      PILZ PNOZ X4 Safety Relay
      by fadi90
      Hi everyone,

      I'm working on repairing a Pilz PNOZ X4 safety relay module. When I opened it up, I found some of the connector pins detached from their pads. I replaced the connector with individual wires, but the issue remains.

      The module is set to dual-channel mode with manual start. In this mode:
      • Y36-Y37 and Y1-Y2 are bridged.
      • 24VDC is applied across A1-A2.
      • It monitors two emergency circuits (S11→S12 and S11→S52).
      • When both are closed (24V present on S12 and S52) and the start button is pressed (S33 connected to S34), the NO contacts (13-14, 23-24, 33-34)
      ...
      X4 - Google Drive
      https://drive.google.com
      06-07-2025, 01:21 AM
    • momaka
      Samsung LN46b530p7f – relay clicks and backlight cycling, sound OK
      by momaka
      I got this TV a little over a year ago from a coworker from my previous job. It’s a Samsung 46” TV, model number LN46b530p7f.

      Problem:
      Backlight cycles On and Off.
      Basically, when the TV is turned On, there is a relay click heard from the TV PS board. The relay cycles On and Off 4 times in about 2-3 second intervals. Each of those 4 times, the backlights also cycle On and Off with the relay. The screen TFT isn’t cracked/damaged and appears to work - I can see a “no signal” image when the backlights turn On briefly – though the image is a bit dull/dark....
      01-17-2019, 11:23 PM
    • Loading...
    • No more items.
    Working...