Needed Vizio VO320e video cable

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • dabone
    Member
    • Aug 2010
    • 30
    #1

    Needed Vizio VO320e video cable

    I'm working on a VO320e that someone else had tried to fix, and I'm in need of the video cable from the main board to the lcd. Apparently the other guy had tried to force it into the UNOPENED connector and buggered it all up.

    I'm located in TN, USA.


    Thanks.

    Later,
    dabone
    Tags: None
    • johnboy1313
      Badcaps Legend
      • Nov 2012
      • 1959
      • USA
      #2
      Re: Needed Vizio VO320e video cable

      I might have one, but I might have scrapped the remnants already. Post a picture of the entire cable and a closeup of both ends.

        Comment

        • dabone
          Member
          • Aug 2010
          • 30
          #3
          Re: Needed Vizio VO320e video cable










          Thanks!

          Later,
          dabone

            Comment

            • ecking767
              Badcaps Veteran
              • Oct 2009
              • 492
              • USA
              #4
              Re: Needed Vizio VO320e video cable

              THE Vizio E321VL used panel and cable

                Comment

                • johnboy1313
                  Badcaps Legend
                  • Nov 2012
                  • 1959
                  • USA
                  #5
                  Re: Needed Vizio VO320e video cable

                  I more than likely tossed it out with the busted panel. I will look when I get home this afternoon.

                  If I don't have it, here's one for $10
                  http://openboxcity.net/0460-2860-003...032-lvds-cable

                    Comment

                    • johnboy1313
                      Badcaps Legend
                      • Nov 2012
                      • 1959
                      • USA
                      #6
                      Re: Needed Vizio VO320e video cable

                      No dice. Maybe you can expose the copper traces a little further up and clip the damaged ends off.

                        Comment

                        Previous template Next

                        Related Topics

                        Collapse
                        • Document Archive
                          HP EliteDesk 800 G3 + GoPro HERO6 Black 4K Ultra HD Video Camera EliteDesk 800 i7-7700 Specification for Upgrade or Repair
                          by Document Archive
                          This specification for the HP EliteDesk 800 G3 + GoPro HERO6 Black 4K Ultra HD Video Camera can be useful for upgrading or repairing a desktop PC that is not working. As a community we are working through our specifications to add valuable data like the EliteDesk 800 G3 + GoPro HERO6 Black 4K Ultra HD Video Camera boardview and EliteDesk 800 G3 + GoPro HERO6 Black 4K Ultra HD Video Camera schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our...
                          09-12-2024, 02:00 PM
                        • JaquesPratt
                          Vizio D32f-E1 Powers on, has backlight, won't boot/no logo, no menu or video
                          by JaquesPratt
                          I have a Vizio D32f-E1 LCD TV that does NOT have a TCON board.

                          This TV recently went through some 'death throes' and now won't boot. The first problem that began to manifest was while watching tv, the screen would 'freeze', and the image would dim over a few seconds until it was very dark. HOWEVER, the audio of the show would continue as normal. I could power off the TV for 5-20 seconds, power back on, and the video would be normal. This would occur 1-3 times when the TV was first started, and would not happen again after the TV was 'warmed up'. Not ideal, but this glitch was manageable....
                          07-16-2024, 01:04 AM
                        • SeaglassPearl
                          Vizio E420VA 5v drops to 3v when power cable is connected
                          by SeaglassPearl
                          Folks, I have a Vizio flat screen that doesn't show any signs of life (and no orange vizio glow either).

                          I tested the voltages from the power board (at the connector) and I can see the 5V supply drops to 3V after the power cable is connected to the main board (5V supply reads as 5V when cable is disconnected from main board). All other rails (12V and 24V) are reading fine.

                          I looked for the usual bloated caps and saw none on either board and no other tell-tall signs (black marks, burned components, etc) on either side of both boards.

                          Given the 5V rail...
                          12-30-2022, 05:55 PM
                        • gcrezz
                          GV-N2060OC-6GD REV 2.0 GIGABYTE video card troubleshooting assistance needed.
                          by gcrezz
                          The issue with this video card is the HDMI port. Specifically on pin 19 (Diode checks on all other pins are normal). When i do a diode check on it from the pin on the board itself, I have nothing. There is also no short on the pin. Resistance reads about 200k. Normally on any HDMI pin 19 I would expect some voltage drop anywhere from .5v to 1.2v but here, I have nothing. The card is operational and can be used via the displayPort ports, but not through the HDMI. Attached you will find the pdf schematics for the card on page 22. I have verified that all of the resistors on this line before the...
                          07-25-2024, 09:49 AM
                        • Tynan Dill
                          Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
                          by Tynan Dill
                          I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

                          Upon bringing it home and plugging it up, it showed a standby light.

                          I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

                          The screen seems to blackout and stay black, but with a flashlight I can see the display.

                          With my Playstation 4 connected via HDMI, and running a game I can hear sound.

                          Assuming...
                          ORIGINAL POWER SUPPLY BOARD
                          7 Photos
                          11-22-2024, 01:46 PM
                        • Loading...
                        • No more items.
                        Working...