Troubleshooting Panasonic CT-25G6E

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Kostamojen
    Member
    • Jun 2011
    • 25

    #1

    Troubleshooting Panasonic CT-25G6E

    Just today my Panasonic ct-25g6e tube tv died. The screen is black, except when I change the input source I get a line at the middle of the screen. I've attached a photo of the screen when changing the input source. As a side note, this tv spent several years in a beach side home, so it was probably subjected to higher than average moisture levels. Any idea what could be wrong?
    Attached Files

Related Topics

Collapse

  • Chrissygizmo
    Panasonic TX-48CX350B backlights but white screen , blank screen
    by Chrissygizmo
    Hi all, I’ve got a problem I hope someone can help me fixi.
    I have a Panasonic TX-48CX350B tv , it powers up ok but the screen is blank, the backlights are working, there’s nothing else though, no picture or sound. I’m not sure what the fault is called whether it’s BLANK/ BLACK/ or WHITE SCREEN I’ve actually came across this before on a similar tv but just ended up scrapping it, I will upload pictures of the boards etc , if anyone could help me I would really appreciate it...
    01-11-2025, 03:18 PM
  • Alicat
    Panasonic Plasma TH-50PZ85U No screen No blinks on red power light
    by Alicat
    Hello,

    Stopped by this site trying to fix my parents Panasonic Plasma TV.

    Model number is TH-50PZ85U

    Power comes on and the red power light stays on solid.

    Did a few checks like hold the power button on for 60 seconds, hold the - Volume while holding the menu button, no luck, still@ blank grey screen as the screen lights up very vague.

    I also hear a few clicks.

    I also think my parents said there was a thunderstorm and the TV failed after that.

    Section 6 in the service manual talks about power and no screen,...
    10-30-2024, 10:09 AM
  • reformatt
    Macbook Air M2 A2681 Kernel panics after screen replacement
    by reformatt
    Just had a customer bring in a M2 MBA A2681 that had had a screen replacement in April at another repairer. Since then, she has been getting intermittent kernel panics. It's an aftermarket screen, and of course it fails in diagnostics as the calibration hasn't been done. The error in the panic log is "No device added after powering on the rails".

    It seems the original repairer has swapped the board and the screen to other MAC's, and said that it isn't a screen issue. From what I understand, by doing a quick search on Google, this is in fact a screen issue. The panic relates...
    07-31-2025, 08:37 PM
  • smic717394
    iphone XS turns off when press on screen.
    by smic717394
    Hi,

    I have a iphone XS that came in for a screen replacement, the screen was badly cracked, and inside missing scues, on the back of the screen still the blue protector, the screen was a LCD. So we replaced the screen and all good, installed the screen and we noticed that pressing the screen with a bit of force but not excessive, the phone dies. After plugging the charger it turns back on, but again if you press it it dies. I open the phone again, and I can't see anything major, with the phone open, if I press on the logic board, battery, charging board, or even putting pressure on...
    07-25-2024, 10:16 AM
  • Zelek11
    Panasonic Plasma screen interference on left half of screen
    by Zelek11
    My Panasonic Plasma model P55VT50 has started displaying "interference" on just the left half of the screen only (left when facing the screen). Sometimes it's concentrated in about the first 30 seconds after startup, then disappears. Other times it's fine at startup and then randomly does it later on. When it flashes the interference it's very quick and doesn't stay on the screen unless it flashes repeatedly in a row.



    This image is a screen shot from a video I took. This is an example of the interference at its worst. Often the interference is much smaller...
    10-14-2022, 04:54 PM
  • Loading...
  • No more items.
Working...