Samsung UN70NU6070F Standby Light flashes twice

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Nicktronic
    Badcaps Veteran
    • Mar 2023
    • 247
    • Canada

    #1

    Samsung UN70NU6070F Standby Light flashes twice

    Hey Everyone,

    So I've got this Samsung and the reported issue is that when powered on the backlight comes on, but no picture, no sound, it will flicker, the standby light will flash red twice and repeat the whole process...each loop lasts about 15 seconds.

    I've googled the issue and understand it is likely a panel/driver board issue, but was hoping the "tape method" could be successful. Before I did that though, I disconnected the left LVDS cable and powered the TV on. This time I got sound, no picture and the two blink standby light stopped. Did the same thing with the right LVDS cable and same result. But with both connected, I get the looping issue described above.

    I tried taping off various pins on each LVDS but was never able to get a picture at all (I was able to stop the looping).

    I tried removing the ribbon cables that join each set of driver boards (see pictures) and everytime I removed one, I was able to stop the loop and get sound.

    In the end, I was able to get a picture a couple times by doing the following;

    1. Power on TV, loop starts.
    2. With the TV on, unplug the LVDS ribbon cable from the far left OR right driver board.
    3. Wait for loop to stop (I hear a samsung jingle and the flashing standby light stops).
    4. Plug the LVDS ribbon cable into the far left OR right driver board.
    5. Ensure when plugging in either LVDS ribbon cable, that I insert the outer end of the cable first and seat it in the connector from outside to inside and secure it.

    At this point I have a picture and can use the TV normally. If i power it off and back on again, the looping starts again...

    And that's my story! Looking for any hope that I can salvage this unit.

    Thanks
    Attached Files

Related Topics

Collapse

  • Document Archive
    Samsung Galaxy Book 2 Notebook Specification for Upgrade or Repair
    by Document Archive
    This specification for the Samsung Galaxy Book 2 Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the Galaxy Book 2 boardview and Galaxy Book 2 schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or download...
    09-07-2024, 05:50 AM
  • tvguy12012012120
    Zombie Samsung UN55NU6900F dead / no standby voltage - randomly came to life after hours of troubleshooting then died
    by tvguy12012012120
    This is my first attempt at troubleshooting a board like this, I know I could just buy a new board but I'm curious to figure out how this works. I've been testing different components in the evenings this week and I think the problem is with the IC failing to start up for some reason. When the board is plugged in there is no standby voltage.

    Then today it randomly sprung to life like a zombie but shortly died thereafter. I have no idea why it would have done that and its the first time I've seen it running. I discharged capacitors on the board last night, then it was sitting today....
    02-07-2025, 05:13 PM
  • provider10
    Samsung UA46ES5660 standby light flashes
    by provider10
    Hi
    Got this Samsung LED tv. Plug set in standby light comes on steady. Switch on Standby light flashes 2 times for a sequence of 5.On the psu I only get the a5v coming out. Disconnect PSU from Main board, backlights come on and all the PSU voltages come up. When in fault mode there are no voltages on any of the regulators on the main board. Yet the processor must be working otherwise it wouldnt change when the set is switched on. Also none of the chips on the main board are getting warm.
    The PSU board is BN44-00502C

    Hoping soene can help

    Thanks
    ...
    02-09-2022, 01:38 AM
  • ChristianBr01
    LED TV Samsung The Frame 55 inch QE55LS03RAU Standby Light only
    by ChristianBr01
    Hello everyone,
    I got a Samsung The Frame 55 inch TV for free from uncle cause it is not turning on anymore. I am in the second year of training as an electrician so I have knowledge already but I am far away from to be a pro.
    The TV has Standby but ist not turning on. A Friend of mine owns a 50 inch Frame TV so I checked the One Connect Box and the One Connect Cable there. Both are good and working normally. I have opened the TV case and measured some voltages on the Board.
    What I already found is that the 12.8V are not an the connector to the main board connector to the power...
    04-23-2025, 01:48 AM
  • Kaar3l
    Samsung QLED QE65Q7FNAT only standby light
    by Kaar3l
    TV: Samsung QLED QE65Q7FNAT
    PSU: BN4400940A
    MB: BN94-12832K

    I got the tv in spring 2024. At that time it started, then ran 60 sec and poweroff. Seemed like reboot issue. I didn't have time and room to check it in summer so I plugged it in and now the standby light is on. I press button on remote, standby light goes off and tries to start?. No picture or backlight on LCD. I thought about removing diodes like in this thread: https://www.badcaps.net/forum/troubl...sung-qled-q60r...
    09-24-2024, 01:35 PM
  • Loading...
  • No more items.
Working...